-
Notifications
You must be signed in to change notification settings - Fork 0
Expand file tree
/
Copy pathprinter_cfg_working.cfg
More file actions
187 lines (156 loc) · 3.83 KB
/
printer_cfg_working.cfg
File metadata and controls
187 lines (156 loc) · 3.83 KB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
# Full confirmation working
# This file contains pin mappings for the Creality Ender-5 Pro with "v4.2.7" board. To
# use this config, during "make menuconfig" select the STM32F103 with
# a "28KiB bootloader" and serial (on USART1 PA10/PA9) communication.
# If you prefer a direct serial connection, in "make menuconfig"
# select "Enable extra low-level configuration options" and select
# serial (on USART3 PB11/PB10), which is broken out on the 10 pin IDC
# cable used for the LCD module as follows:
# 3: Tx, 4: Rx, 9: GND, 10: VCC
# Flash this firmware by copying "out/klipper.bin" to a SD card and
# turning on the printer with the card inserted. The firmware
# filename must end in ".bin" and must not match the last filename
# that was flashed.
# See docs/Config_Reference.md for a description of parameters.
[stepper_x]
step_pin: PB9
dir_pin: PC2
enable_pin: !PC3
microsteps: 16
rotation_distance: 40
endstop_pin: ^PA5
position_endstop: 220
position_max: 220
homing_speed: 50
[stepper_y]
step_pin: PB7
dir_pin: PB8
enable_pin: !PC3
microsteps: 16
rotation_distance: 40
endstop_pin: ^PA6
position_endstop: 220
position_max: 220
homing_speed: 50
[stepper_z]
step_pin: PB5
dir_pin: PB6
enable_pin: !PC3
microsteps: 16
rotation_distance: 4 # 4 for new leadscrew, 8 for old
#position_endstop: 0.0 # disable to use BLTouch
#endstop_pin: ^PA7 # disable to use BLTouch
endstop_pin: probe:z_virtual_endstop # enable to use BLTouch
position_min: -5 # enable to use BLTouch
position_max: 300
[safe_z_home] # enable for BLTouch
home_xy_position: 154, 126
speed: 100
z_hop: 10
z_hop_speed: 5
[bltouch] # enable for BLTouch
sensor_pin: ^PB1
control_pin: PB0
x_offset: -44
y_offset: -16
z_offset: 3.35
speed: 3.0
[bed_mesh] # enable for BLTouch
speed: 100
mesh_min: 0, 0
mesh_max: 176, 204 # bed size - bltouch x_offset, y_offset
algorithm: bicubic
probe_count: 3,3
fade_start: 1
fade_end: 10
fade_target: 0
[gcode_macro M851]
gcode:
G28
probe_calibrate
[gcode_macro G32]
gcode:
G28
delta_calibrate
G1 X0 Y0 F4200
save_config
[gcode_macro G29]
gcode:
G28
bed_mesh_calibrate
G1 X0 Y0 Z15 F4200
save_config
[extruder]
max_extrude_only_distance: 100.0
step_pin: PB3
dir_pin: PB4
enable_pin: !PC3
microsteps: 16
rotation_distance: 33.500
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PA1
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC5
control: pid
pid_Kp: 21.527
pid_Ki: 1.063
pid_Kd: 108.982
min_temp: 0
max_temp: 250
pressure_advance: 0.56
[heater_bed]
heater_pin: PA2
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC4
control: pid
pid_Kp: 54.027
pid_Ki: 0.770
pid_Kd: 948.182
min_temp: 0
max_temp: 130
[fan]
pin: PA0
[mcu]
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
baud: 115200
restart_method: command
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100
[display]
lcd_type: st7920
cs_pin: PB12
sclk_pin: PB13
sid_pin: PB15
encoder_pins: ^PB14, ^PB10
click_pin: ^!PB2
[board_pins]
aliases:
EXP1_1=PC6,EXP1_3=PB10,EXP1_5=PB14,EXP1_7=PB12,EXP1_9=<GND>,
EXP1_2=PB2,EXP1_4=PB11,EXP1_6=PB13,EXP1_8=PB15,EXP1_10=<5V>,
PROBE_IN=PB0,PROBE_OUT=PB1,FIL_RUNOUT=PC6
#verify z height, mm level changes do occur when moving the printer, etc.
#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# 0.188750, 0.098750, 0.161250
#*# 0.052500, -0.010000, 0.087500
#*# 0.097500, 0.028750, 0.073750
#*# tension = 0.2
#*# min_x = 0.0
#*# algo = bicubic
#*# y_count = 3
#*# mesh_y_pps = 2
#*# min_y = 0.0
#*# x_count = 3
#*# max_y = 204.0
#*# mesh_x_pps = 2
#*# max_x = 176.0
[include mainsail.cfg]