All notable changes to this project will be documented in this file.

• Possibility to add a prefix and postfix for write messages

• Plain text search is used now for pattern search
• Automatically set a pattern search within read message when selecting single process data or parameter
• Improved handling if connecting SLT device

• Show result of pattern search within the IO-Link payload on UI
• Show status info of IODD Interpreter on UI

• New function to edit amount of extra bytes to add to process data byte length

• FlowConfig handling

• OnNewRawReadMessage_INSTANCE_PORT_MESSAGENAME provides timestamp as 2nd event parameter (used for FlowConfig)

• Minor docu improvements
• Minor update of readMessageName check

• DeviceID was shown as ProductID in UI
• 'OnNewDataAuto' FlowConfig block did not work with initial load of persistent data
• Legacy bindings of ValueDisplay elements and FileUpload feature within UI did not work if deployed with VS Code AppSpace SDK
• UI differs if deployed via Appstudio or VS Code AppSpace SDK
• Fullscreen icon of iFrame was visible

• Issue to create new instances (introduced with v3.0.0)

• Provide features even without CSK_Module_IODDInterpreter
• Create readMessages without IODD information, by setting start-/endByte (or bit position within byte) and unpack format
• Optionally search and cut relevant part out of created JSON within readMessage
• Register to event to forward content as writeMessage
• New FlowConfig block 'OnNewDataAuto' which automatically creates readMessages and optionally checks to power selected port (WARNING: Do NOT mix with manual readMessage setup)
• New FlowConfig block 'WriteProcessData'
• React on "OnStopFlowConfigProviders" event of FlowConfig modul to stop pulling IO-Link data
• Check and handle different kind of IOLink.SMI APIs
• Function to delete all existing readMessages
• Check if persistent data to load provides all relevant parameters. Otherwise add default values
• Selectable if timers for readMessages should start automatically after parameters were loaded

• Changed event name "OnNewReadMessage_PORT_MESSAGENAME" to "OnNewReadMessage_INSTANCE_PORT_MESSAGENAME" to make it possible to switch between ports during runtime
• Do not start readMessage timers automatically with creation of readMessage
• Use new event 'OnNewRawReadMessage_INSTANCE_PORT_MESSAGENAME" within FlowConfig (only providing data content as first parameter)
• If using FlowConfig, start readMessage timers after 5 seconds
• Add info about port within "OnNewIOLinkPortStatus" event
• Add list of ports related to instances within "getInstancePortMap" function
• Better handling if CSK_IODDInterpreter is not available

• Issue with CSK_UserManagement support
• Error if sending process data without any selection
• Error in handling IODD data

• writing of process data and parameters is available again

• Now it is possible to read subindexes (even if the subindex access is not supported). Requires IODD interpreter v2.1.0 or more

• Speeding up of data parsing when reading from IO-Link device

• Supports FlowConfig feature to provide data of IO-Link ReadMessage
• Changed event name of readMessages from 'readMessage[PORT][MESSAGENAME] to 'OnNewReadMessage_[PORT]_[MESSAGENAME]
• Possible to pause timers for readMessages
• Function 'getPort' for currently selected instance
• Provide version of module via 'OnNewStatusModuleVersion'
• Function 'getParameters' to provide PersistentData parameters
• Check if features of module can be used on device and provide this via 'OnNewStatusModuleIsActive' event / 'getStatusModuleActive' function
• Function to 'resetModule' to default setup

• Better interaction with CSK_IODDInterpreter (version 2.0.0 needed)
• Check status of port within instance thread (prevent to get data if sensor is not in operating mode)
• Port only changeable if currently inactive
• New UI design available (e.g. selectable via CSK_Module_PersistentData v4.1.0 or higher), see 'OnNewStatusCSKStyle'
• Preset names for ReadMessages / WriteMessages instead of renaming them after creation
• check if instance exists if selected
• 'loadParameters' returns its success
• 'sendParameters' can control if sent data should be saved directly by CSK_Module_PersistentData
• Added UI icon and browser tab information

• IODD parsing
• Check if readMessage exists before trying to delete it

• Initial commit