Ask any power electronics engineer which substrate they reach for when a design pushes past 10–15 watts of continuous dissipation, and the answer is rarely FR-4. That choice usually comes down to one number: thermal conductivity. Standard FR-4 sits at roughly 0.3 W/mK in the Z-axis. Bergquist vs FR-4 PCB comparisons tell the rest of the story — Bergquist Thermal Clad dielectrics deliver 2.4 to 4.1 W/mK, and the aluminum or copper base underneath adds another zero to that figure entirely.

This article gets into the numbers honestly, covers the scenarios where FR-4 still makes sense, and explains why Bergquist Thermal Clad’s metal core architecture routinely outperforms FR-4 in high-power LED, power conversion, motor drive, and automotive applications.

Understanding the Core Problem: Why FR-4 Struggles with Heat

FR-4 is a glass-reinforced epoxy laminate — and that same epoxy matrix that makes it such an effective electrical insulator is precisely what makes it a thermal bottleneck. At its core, FR-4 is an excellent electrical insulator but a poor thermal conductor. Its thermal conductivity is approximately 0.3 W/mK, and the same property making it a great electrical insulator also makes it a thermal barrier.

The problem compounds in the Z-axis, which is the direction heat actually needs to travel in a surface-mount assembly. The thermal conductivity path through the Z-axis is typically as low as 0.29 W/mK. Since heat generated by surface-mount devices must first pass vertically through this Z-axis insulating layer before reaching internal or bottom heat-dissipation planes, effective thermal management strategies must focus on bypassing this vertical bottleneck.

The consequence is predictable: In high-power applications, this can result in temperature rises of 50°C or more above ambient conditions, risking component failure. Additionally, FR-4 has a glass transition temperature of around 130–140°C, beyond which it loses structural integrity, making it unsuitable for extreme heat environments.

Component life typically decreases according to the Arrhenius law as temperature rises — a common empirical rule suggests lifespan approximately halves for every 10°C increase in temperature. That rule of thumb is worth writing on the whiteboard before any high-power material selection discussion begins.

What FR-4 Engineers Do to Compensate — And Why It Has Limits

Strategies for high-temperature FR-4 PCB designs include using thermal vias, incorporating heat sinks, and selecting complementary materials to reduce thermal resistance in FR-4. These workarounds are real and sometimes sufficient:

• Dense thermal via arrays beneath power devices can reduce effective Z-axis resistance
• Heavy copper (2–4 oz) improves in-plane spreading
• External heatsinks with TIM pads redirect heat away from the board
• High-Tg FR-4 variants push the glass transition temperature to 170–180°C

But each workaround adds cost, assembly complexity, and board area. To compensate for its poor heat dissipation, FR-4 often requires external cooling solutions like heat sinks or forced air systems, increasing design complexity and cost. For applications pushing beyond 10–15 watts of power dissipation per square inch, FR-4 often fails to meet thermal requirements, making IMS a better choice.

What Makes Bergquist Thermal Clad Different from FR-4

Bergquist Thermal Clad is an Insulated Metal Substrate (IMS) — a fundamentally different architecture from FR-4. Bergquist’s Thermal Clad dielectric is a thin, thermally conductive layer bonded to an aluminum or copper substrate for heat dissipation. The key to Thermal Clad’s superior performance lies in its dielectric layer. This layer offers electrical isolation with high thermal conductivity and bonds the base metal and circuit foil together. Other manufacturers use standard prepreg as the dielectric layer, but prepreg doesn’t provide the high thermal conductivity and resulting thermal performance required.

The dielectric is a proprietary polymer/ceramic blend that gives Thermal Clad its excellent electrical isolation properties and low thermal impedance. The polymer is chosen for its electrical isolation properties, ability to resist thermal aging and high bond strengths. The ceramic filler enhances thermal conductivity and maintains high dielectric strength. The result is a layer of isolation which can maintain these properties even at 0.003″ (76µm) thickness.

The three-layer build — copper circuit, ceramic-polymer dielectric, metal base — creates a direct and controlled thermal path from solder joint to heatsink that FR-4 simply cannot replicate without significant added hardware.

Bergquist vs FR-4 PCB: Head-to-Head Material Properties

The column that matters most in a thermal-limited design is the top one. At 4.1 W/mK (HT-04503), Bergquist’s dielectric is roughly 14× more thermally conductive than standard FR-4. In a substrate system where the dielectric layer is the dominant thermal resistance, that gap translates directly into cooler components.

The Real-World Thermal Impact: A Practical Comparison

The abstract conductivity numbers only become meaningful when you model them against an actual power stage. Consider a 25W MOSFET in a D2PAK package with a mounting footprint of approximately 1.5 cm². The junction-to-case resistance is 1.0°C/W. You want to know the temperature rise across the substrate dielectric layer alone.

Using standard FR-4 (0.3 W/mK, 150µm thick):

ΔT (dielectric) = (Power × thickness) / (conductivity × area) = (25W × 0.00015m) / (0.3 W/mK × 0.00015 m²) = 83°C across the dielectric layer

Using Bergquist HT-04503 (4.1 W/mK, 76µm thick):

ΔT (dielectric) = (25W × 0.000076m) / (4.1 W/mK × 0.00015 m²) = 3.1°C across the dielectric layer

That 80°C difference doesn’t come from a theoretical model — it comes from the physical heat flow equation. In a high-power LED application, an IMS PCB can reduce the junction temperature of the LEDs by up to 20–30°C compared to FR-4 under the same operating conditions. Lower temperatures translate to better efficiency and a longer lifespan for the components.

Thermal Resistance: The Designer’s True Comparison Metric

Thermal resistance — measured as °C/W or °C·cm²/W — is the number to use when comparing designs, not conductivity alone. FR-4 typically has a thermal resistance of 50–70 °C/W per square inch, much higher than metal-core PCBs at around 10–20 °C/W.

Where Bergquist Thermal Clad Wins by a Clear Margin

High-Power LED and Solid-State Lighting

This is where the Bergquist vs FR-4 PCB decision is most clear-cut. LED junction temperature directly controls lumen output, color point, and L70 lifetime (the point where output degrades to 70% of initial). The low thermal impedance of Thermal Clad dielectrics outperforms other PCB materials and offers a cost-effective solution, eliminating additional LEDs for simplified designs.

On a 100W street light array, the delta between FR-4 and Thermal Clad HPL is not just a thermal number — it can mean the difference between an LED array lasting 50,000 hours versus 25,000 hours. Replacing burned-out fixture modules in a city-wide streetlight deployment has real maintenance cost implications that dwarf the material cost premium.

Motor Drives and Variable Frequency Drives

Bergquist’s Thermal Clad PCBs offer superior thermal conductivity, electrical insulation, and environmental compliance, making them ideal for motor drives where heat is a constant challenge. In a VFD, the IGBT or SiC MOSFET switch bank is the dominant heat source, and it cycles between full-on and off at switching frequencies from a few kHz to over 100 kHz. The thermal fatigue on the substrate dielectric under those conditions rules out standard FR-4 on reliability grounds, not just thermal performance grounds.

Automotive Power Electronics

As the automotive industry has shifted toward electric vehicles and advanced driver-assistance systems, these systems demand reliable electronic components that can withstand extreme environments, including fluctuating temperatures and vibrations. Bergquist PCBs handle components like inverters, battery management systems, and electronic control units with ease.

FR-4 is not absent from automotive electronics — most ECU logic boards are FR-4 — but the moment you cross into underhood power electronics with sustained dissipation above 5–10W per square inch, the thermal and temperature-cycling fatigue limits of FR-4 push you toward an IMS solution.

Power Conversion and Solid-State Relays

Due to the size constraints and watt-density requirements in DC-DC conversion, Thermal Clad has become a favored choice. It can be used in almost every form-factor and fabricated in a wide variety of substrate metals, thicknesses, and copper foil weights.

In compact telecom converters or onboard chargers, eliminating the external heatsink assembly that FR-4 requires — mica insulators, spring clips, thermal grease — translates directly to lower BOM cost and fewer assembly steps. With the use of etched traces on the board, interconnects can be removed. This thermal clad helps to replace discrete devices at the board level and allows for increased power density.

Where FR-4 Is Still the Right Call

This is not a one-sided comparison. FR-4 earns its place in the vast majority of PCB designs for a reason.

For RF and microwave applications where loss tangent and dielectric constant stability matter more than thermal conductivity, FR-4 is also not the right call — but neither is Bergquist Thermal Clad. That segment is where Arlon PCB materials (e.g., the AD and CLTE-XT series) are the correct specification. Knowing which of these three material families fits your design is the mark of a well-rounded PCB engineer.

Fabrication and Cost: Honest Trade-offs

Any honest comparison has to acknowledge the cost and process differences between FR-4 and Bergquist Thermal Clad.

Material and Fabrication Cost

Thermal Clad panel stock costs more than FR-4 — sometimes substantially more depending on grade. The HT and HPL series are particularly premium. Beyond material, the fabrication process requires appropriate tooling: carbide drill bits rated for aluminum composite, single-flute CNC router bits to avoid galling, and depth-controlled V-scoring for clean panel singulation.

Design Complexity Trade-offs

Thermal Clad is a cost-effective solution which can eliminate components, allow for simplified designs, smaller devices, and an overall less complicated production process. Cooling with Thermal Clad can eliminate the need for heat sinks, device clips, cooling fans, and other hardware. An automated assembly method will reduce long-term costs.

The fabrication cost premium on Thermal Clad is partially offset by BOM simplification — removing individual mica pads, spring clips, thermal grease application, and heatsink hardware from the assembly process. On high-volume production, that per-unit labor saving can be significant.

Useful Technical Resources for Bergquist vs FR-4 PCB Design

Every engineer comparing these materials at the design stage should have these documents bookmarked:

5 FAQs: Bergquist Thermal Clad vs FR-4 PCB

Q1: Can I use FR-4 with thermal vias instead of Bergquist Thermal Clad to save cost?

Sometimes yes, but with real limits. Dense thermal via arrays (via-in-pad, filled and capped) can reduce FR-4 thermal resistance meaningfully — bringing it from 50–70 °C·cm²/W down to perhaps 15–25 °C·cm²/W for a well-designed via matrix. If your power dissipation is below ~5W per component and you have layout area to work with, this approach can work and costs less. Above that threshold, or in any design where board size is constrained, Thermal Clad’s consistent 0.30–0.71 °C·cm²/W performance and elimination of external hardware generally wins on total system cost and reliability. The thermal via approach also adds layout complexity and can compromise signal integrity around high-frequency switching nodes.

Q2: Is Bergquist Thermal Clad much harder to fabricate than FR-4?

It requires different tooling and process awareness, but it is not exotic. The aluminum base machines differently from glass-epoxy — carbide drill bits wear faster, routing requires single-flute tools to prevent galling, and V-scoring depth requires tighter control. Standard SMT assembly, LPI solder mask, ENIG or HASL surface finish, and lead-free reflow profiles all transfer directly from FR-4 processes without modification. Any PCB fabricator regularly working with aluminum MCPCB has the right equipment. The main DFM consideration is getting the material spec note right on the drawing: base metal alloy, dielectric grade, copper weight, and any selective dielectric removal requirements.

Q3: Does Bergquist Thermal Clad support multilayer designs like FR-4?

Not in the same way. Standard FR-4 multilayer PCBs with 4, 6, or 8 layers are straightforward. Thermal Clad is primarily a single-circuit-layer substrate. Two-layer configurations are achievable using Bergquist Bond-Ply to laminate a second FR-4 or Thermal Clad circuit to the back of the base metal, but buried vias, blind vias, and standard multilayer constructions are not. For designs that need both high-power thermal management and complex multilayer routing, a hybrid approach is common: power devices on a Thermal Clad section, logic and control circuitry on a conventional FR-4 PCB, interconnected by press-fit pins or flex cable.

Q4: When does it make financial sense to upgrade from FR-4 to Bergquist Thermal Clad?

The crossover point depends on what FR-4 forces you to add to compensate for its thermal limitations. Count the BOM cost of individual TO-220/TO-247 insulators (mica or Kapton), thermal grease or phase-change TIM, heatsink hardware, and assembly labor for torqued fasteners. In a motor drive or power supply with six to twelve power devices, that hardware cost per board can easily reach $3–8 in materials alone, plus the assembly time. Thermal Clad eliminates all of it. The material premium on the board itself is often recovered within the first several hundred units, and the reliability improvement — particularly in warranty cost reduction — frequently makes the financial case compelling even before you reach high volumes.

Q5: Can Bergquist Thermal Clad replace ceramic substrates like DBC?

Thermal Clad can replace large-area ceramic substrates. It can also be used as a mechanically durable support for ceramic spacers or direct bonded copper sub assemblies. The copper circuit layer of Thermal Clad has more current carrying capability than thick-film ceramic technology. For moderate-power applications — say, up to 50–100W single device — the substitution of Thermal Clad for DBC (Direct Bonded Copper on alumina) is viable and typically reduces cost and brittleness risk. At very high power density with bare die mounting and tight thermal budgets, DBC or AMB (Active Metal Brazed) ceramics on aluminum nitride maintain an edge in bulk thermal conductivity. Thermal Clad sits between FR-4 and DBC in both performance and cost — which happens to be exactly where most industrial and automotive power electronics designs live.

Final Thoughts on Bergquist vs FR-4 PCB

The Bergquist vs FR-4 PCB choice is not actually complicated once you run the thermal numbers. FR-4 is a superb material for the overwhelming majority of electronic designs where power dissipation is moderate and thermal management can be handled with copper planes and selective use of heatsinks. The moment a design needs to move more than roughly 10W per square inch through the substrate consistently, FR-4’s 0.3 W/mK Z-axis conductivity becomes the design’s weak link.

Bergquist Thermal Clad’s proprietary ceramic-polymer dielectric eliminates that weak link. The result — direct junction-to-metal-base thermal conduction, no added TIM hardware, consistent and well-characterized thermal resistance values — is precisely why it has been the benchmark MCPCB dielectric for LED, motor drive, power conversion, and automotive power electronics for decades.

Make the material decision early, run the thermal resistance stack calculation honestly, and choose the dielectric grade (HPL, HT, MP, or LM) that fits your voltage isolation and thermal budget. That order of operations will keep your design out of warranty returns and off the teardown bench.

The post Bergquist Thermal Clad vs Standard FR-4: Why Metal Core PCB Wins for Thermal Management appeared first on RayPCB.

If you’ve spent any time specifying materials for high-power LED drivers, motor control boards, or automotive power modules, you’ve almost certainly landed on Bergquist Thermal Clad PCB as a candidate material. It shows up in the datasheet for half the metal-core substrates on the market, and with good reason — the dielectric technology behind it has been setting the benchmark for insulated metal substrates (IMS) for decades.

This guide breaks down everything a working PCB engineer needs to know: the dielectric series, real-world thermal numbers, design rules, fabrication gotchas, and when Thermal Clad genuinely outperforms the competition versus when a cheaper alternative will do the job just fine.

What Is Bergquist Thermal Clad PCB?

Bergquist Thermal Clad is a metal-core PCB (MCPCB) substrate technology developed by The Bergquist Company, now operating under Henkel Corporation’s Electronic Materials division and also carried by successor brands such as TCLAD Inc. At its core — literally — the product is a laminate stack: a copper circuit foil bonded through a proprietary thermally conductive dielectric layer to an aluminum or copper baseplate.

What makes it different from generic aluminum-base PCBs is that dielectric. The technology of Thermal Clad resides in the dielectric layer — it is the key element for optimizing performance. The dielectric is a proprietary polymer/ceramic blend that gives Thermal Clad its excellent electrical isolation properties and low thermal impedance. The polymer is chosen for its electrical isolation properties, ability to resist thermal aging and high bond strengths. The ceramic filler enhances thermal conductivity and maintains high dielectric strength — resulting in a layer of isolation that can maintain these properties even at 0.003″ (76µm) thickness.

In other words, competing MCPCB products often use standard prepreg as the dielectric. Other manufacturers use standard prepreg as the dielectric layer, but prepreg doesn’t provide the high thermal conductivity and resulting thermal performance required to help assure the lowest possible operating temperatures and brightest light output for high-intensity LEDs. That’s the core value proposition in a single sentence.

The Three-Layer Structure

Every Bergquist Thermal Clad board follows a consistent build:

The base metal is where the heat ultimately goes. Copper gives you better conductivity (390 W/mK), but aluminum is far more cost-effective at 205 W/mK and handles the thermal load in the overwhelming majority of commercial applications.

The Four Bergquist Thermal Clad Dielectric Series

This is the most important section for any engineer spec’ing a board. Thermal Clad circuit board materials are available from The Bergquist Company in four different thermal conductivities: High Power Lighting (HPL), High Temperature (HT), Low Modulus (LM), and Multi-Purpose (MP). Each is engineered for a specific operating envelope.

HPL — High Power Lighting

HPL is the go-to dielectric for demanding LED applications. HPL is a dielectric specifically formulated for high power lighting LED applications with demanding thermal performance requirements. This thin dielectric at 0.0015″ (38µm) has an ability to withstand high temperatures with a glass transition of 185°C and phenomenal thermal performance of 0.30°C/W.

The part number most commonly seen in the field is HPL-03015, which refers to the 0.030″ (0.76mm) base aluminum thickness with 1 oz (35µm) copper. Bergquist Thermal Clad Metal Core PCBs minimize thermal impedance and conduct heat more effectively and efficiently than standard printed wiring boards.

When to use HPL: Any design where junction temperature is the dominant constraint — high-wattage COB LEDs, stadium lighting, projector systems, and backlit display modules.

HT — High Temperature

The HT series offers a balance of elevated operating temperature tolerance and strong thermal conductivity. The HT-04503 provides high thermal conductivity of 4.1 W/m-K for high temperature applications, is lead-free solder compatible, Eutectic AuSn compatible, RoHS compliant and environmentally green, and available on all aluminum and copper metal substrates.

The HT-07006 variant steps up the dielectric thickness to 0.006″ (152µm) while maintaining that same 4.1 W/mK conductivity, making it the right call when you need more electrical isolation — say, above 480V AC systems. The HT-07006 features a very low thermal resistance of 0.71°C-cm²/W combined with high thermal conductivity of 4.1 W/m-K, and the product is certified RoHS compliant.

When to use HT: Power conversion, motor drives, inverters, and any system needing eutectic gold-tin solder compatibility or operation above 150°C continuous.

MP — Multi-Purpose

MP-06503 is the workhorse of the Thermal Clad lineup — a cost-optimized general-purpose substrate covering a huge range of mid-power applications. With a thermal resistance of 0.58°C-cm²/W, MP-06503 provides efficient heat dissipation, ensuring optimal thermal management for electronic devices. It exhibits a thermal conductivity of 2.4 W/m-K, enabling efficient heat transfer across the PCB.

The technology of Thermal Clad resides in the dielectric. Optimal storage for the MP-06503 is 5 to 25°C for a 12-month shelf life. Worth noting for anyone managing incoming materials.

When to use MP: Solid-state relays, power supplies, battery management modules, and mid-power LED modules where budget pressure is real but you still need something better than off-brand MCPCB stock.

LM — Low Modulus

LM is a less commonly discussed variant but worth knowing. The lower modulus dielectric provides improved mechanical compliance, which matters when you have CTE mismatch concerns between a large component and the substrate. This is especially relevant in applications with severe thermal cycling, where a brittle dielectric can delaminate over time.

When to use LM: Automotive underhood applications, aerospace modules, or any design where the assembly will see hundreds of thermal cycles between cold soak and operating temperature.

Bergquist Thermal Clad Dielectric Quick-Reference Table

Values are nominal. Always verify against the specific product datasheet for your revision.

Bergquist Thermal Clad vs. FR-4 vs. Generic MCPCB

One of the most common engineering questions is: “Do I actually need Thermal Clad, or will a cheaper metal-core board do the job?” The answer depends entirely on your thermal budget.

Bergquist Thermal Clad Metal Core PCBs minimize thermal impedance and conduct heat more effectively and efficiently than standard printed wiring boards. The low thermal impedance of Thermal Clad dielectrics outperforms other PCB materials and offers a cost-effective solution eliminating additional LEDs for simplified designs and an overall less complicated production process.

Here’s how the materials stack up for a typical 40W power stage application:

The numbers tell the story. If you’re running a 5W LED module, a decent generic MCPCB is probably sufficient. At 20W and beyond — particularly if junction temperature headroom is tight — the thermal conductivity gap between Bergquist and generic alternatives starts translating directly into either shorter LED lifespan or the need for a larger heatsink.

Thermal Clad can replace large-area ceramic substrates. It can also be used as a mechanically durable support for ceramic spacers or direct bonded copper subassemblies. The copper circuit layer of Thermal Clad has more current carrying capability than thick-film ceramic technology.

This makes Thermal Clad a direct substitute for DBC (Direct Bonded Copper) ceramics in moderate-power applications — at a significantly lower fabrication cost.

Key Applications of Bergquist Thermal Clad PCB

LED Lighting — The Primary Use Case

LED lighting has truly transformed how we light up our spaces, offering energy-efficient alternatives that stand the test of time. But as LEDs get more powerful and brighter, managing heat becomes a bigger concern. That’s where Bergquist Thermal Clad PCBs come in, providing the perfect fix for LED lighting designs.

The HPL dielectric series was specifically engineered for this market. Bergquist provides critical thermal management support for a myriad of power LED applications including medical, signage, signal, transportation, aircraft, automotive, security, portable, theatrical, commercial, residential, and street lighting applications.

For a street lighting or high-bay LED array running at 100W+, the thermal budget is unforgiving. Using HPL with a direct thermal path from LED emitter to aluminum heatsink — with no thermal grease or TIM interface — delivers measurably lower Tj compared to any standard FR-4 or generic MCPCB solution.

Automotive and EV Power Electronics

The automotive industry has seen a substantial shift toward electric vehicles (EVs) and advanced driver-assistance systems (ADAS). These systems demand reliable electronic components that can withstand extreme environments, including fluctuating temperatures and vibrations. Bergquist PCBs meet these challenges with their high thermal conductivity, reliability, and rugged construction. Bergquist PCBs are designed to handle components like inverters, battery management systems (BMS), and electronic control units (ECUs) with ease.

Underhood environments routinely see ambient temperatures above 100°C combined with aggressive vibration profiles. The HT and LM series both address this — HT for raw thermal performance, LM where fatigue life under thermal cycling is the constraint.

Power Conversion and Motor Drives

Bergquist thermal clad is a preferred choice for engineers for power conversion due to its watt-density and size. Motor drives are also ideal for Bergquist thermal clad — they are good dielectric material and feature high watt density, enabling fabrication and installation of compact form factors into motor drives.

Switching power supplies, VFDs, and servo drives all pack high-current components (IGBTs, MOSFETs, diode bridges) into tight footprints. Thermal Clad eliminates the need for individual TO-220 or TO-247 insulators (mica, Kapton, silicone pads) under power devices — the board itself provides the isolation, and the assembly simplification is real.

Industrial and Aerospace

TCLAD Insulated Metal Substrate (IMS) PCBs deliver high efficiency, exceptional durability, and long-term reliability for mission-critical electronics operating in the extreme conditions of aerospace and defense applications.

In harsh-environment applications, the UL certification and controlled manufacturing processes of Bergquist materials are often a procurement requirement, not just a nice-to-have.

Design Guide for Bergquist Thermal Clad PCB

Getting the most out of Thermal Clad starts at the design stage, not at the FAI.

Dielectric Selection and Thermal Budget

Before you pick a dielectric grade, run the numbers. The thermal path from component junction to ambient is a series of resistances. The Thermal Clad layer is just one of them. Your calculation should include:

1. Junction-to-case resistance of the component (Rθjc from datasheet)
2. Solder joint resistance (typically 0.1–0.5°C/W for SMD)
3. Thermal Clad dielectric resistance (from the product spec)
4. Base metal spreading resistance
5. Thermal interface to heatsink (if applicable)
6. Heatsink-to-ambient (Rθsa)

If your calculation shows Tj is within 10°C of the component’s maximum at full load, you need either a lower-resistance dielectric (HPL vs. HT) or a thicker copper circuit layer.

Copper Circuit Layer Thickness

The copper circuit layer of Thermal Clad has more current carrying capability than thick-film ceramic technology. However, trace width still matters. The circuit layer is the component-mounting layer in Thermal Clad. Current carrying capability is a key consideration because this layer typically serves as a printed circuit, interconnecting the components of the assembly. On Thermal Clad, smaller lines will not overheat, but they will increase the waste thermal heat of the assembly.

Use 2 oz or 3 oz copper (70µm or 105µm) for power traces wherever possible. On Thermal Clad, the heat generated by I²R losses in copper traces conducts straight down through the dielectric — which is a feature, not a bug.

Dielectric Thickness and Voltage Isolation

The relationship between dielectric thickness and working voltage is non-linear. For applications with an expected voltage over 480 Volts AC, Bergquist recommends a dielectric thickness greater than 0.003″ (76µm). This immediately rules out HPL (38µm) for mains-connected power stages above that threshold — HT-04503 or HT-07006 becomes the correct choice.

Thermal Via and Copper Pour Strategy

Unlike multilayer FR-4 PCBs where thermal vias punch heat down through the board, Thermal Clad does not support plated through-holes in the traditional sense. The base metal is electrically isolated by the dielectric. What you can do:

• Use large copper pours on the circuit layer directly beneath high-power components to spread heat laterally before it enters the dielectric
• Implement selective dielectric removal (SDR) processes — where the dielectric is locally removed to create direct copper-to-baseplate contact for critical die-attach applications. Bergquist has developed a process for selectively removing dielectric to expose the baseplate, which is used in advanced power module assembly.

Design Rule Quick Reference

Fabrication and Assembly Considerations

Drilling and Routing

Aluminum-base Thermal Clad machines differently from FR-4. Drill bits designed for FR-4 will work but wear faster. For production runs, use carbide bits specified for aluminum composite materials. Routing should use single-flute upcut bits to avoid aluminum galling on the tool. Punching is viable for simple shapes but requires careful die design — the ceramic-filled dielectric can crack if punch clearance is excessive.

Solder Mask and Surface Finish

Standard liquid photoimageable (LPI) solder mask applies to Thermal Clad circuit layers without process modification. Surface finish options are similar to standard PCBs:

Reflow Soldering

Standard SMT reflow profiles work on Thermal Clad. The aluminum base actually helps here — its thermal mass smooths out temperature ramp rates across the board. Be aware that: (a) the high thermal conductivity means large heat sinks or ground pours may require profiling adjustment, and (b) component leads or packages with high CTE mismatch relative to aluminum can stress solder joints under thermal cycling. For critical reliability, validate your solder joint fatigue life with FEA if the board will see >1000 thermal cycles.

Wire Bonding and Direct Die Attachment

The HT dielectrics are UL solder rated at 325°C/60 seconds, enabling Eutectic Gold/Tin solders — which opens the door to direct die-attach processes used in power module assembly. Wire bonding is supported on appropriately finished pads. Wire bonding is a connection technique that utilizes the surface mount ability of a PCB. In thermal clad assembly, pin headers and pin connectors are very useful when attaching an FR-4 panel to a thermal clad assembly.

Bergquist Thermal Clad vs. Arlon PCB Materials

When evaluating high-performance PCB substrate families, engineers often compare Bergquist Thermal Clad against other specialty laminates. Arlon PCB materials — particularly the AD/CLTE series — occupy a different part of the design space: they target high-frequency RF and microwave applications rather than thermal management. If your design requires both RF performance and thermal management (say, a high-power amplifier module), you may end up using Arlon-class materials for the RF section and Thermal Clad for the power stage section within the same assembly.

The comparison table below covers the most common design scenarios:

Neither material is universally superior — they solve different problems. Knowing when to reach for each is the mark of an experienced designer.

Where to Source Bergquist Thermal Clad Materials and PCBs

Raw Material Distributors (Panel Stock)

If you’re qualifying the material yourself or sending it to a contract manufacturer, the following sources stock Bergquist Thermal Clad laminates:

Useful Technical Resources and Datasheets

Below is a curated list of official and reference documents that should be bookmarked by any engineer working with Bergquist Thermal Clad PCB:

Pros and Cons of Bergquist Thermal Clad PCB

No material is perfect. Here is an engineer’s honest assessment:

Advantages

Bergquist thermal clad PCBs feature low thermal impedance which outperforms other insulators, allowing cooler operation. These thermal clad PCBs increase the level of durability because designs are simple and components run cool. The thermal clad removes the thermal interface and uses thermal solder joints, making assemblies run cooler. These thermal clad PCBs allow automated pick-and-place for SMDs, which minimizes production costs. Bergquist thermal clad minimizes board space and replaces other components like heat sinks, and helps eliminate rubber or mica insulators under power devices.

In practical terms this means: fewer BoM lines (no individual component TIMs), simplified assembly (no hardware-torqued insulators), and PCB-level thermal management that scales cleanly from prototype to production.

Disadvantages and Limitations

• Cost: Panel stock is significantly more expensive than FR-4, and fabrication costs are higher due to specialized tooling and process parameters.
• No plated through-holes to the baseplate: You cannot create a conventional electrical via to the base metal. All electrical routing is on the circuit side, which limits you to single-layer or specially configured two-layer constructions.
• Dielectric thickness limitation on voltage rating: HPL’s ultra-thin dielectric limits isolation voltage — it is not suitable for line-voltage isolation on its own at high power levels.
• Panelization and singulation: V-scoring works but requires controlled depth. CNC routing with appropriate tooling is preferred for clean edges.
• Heavier than FR-4 equivalents: The aluminum base adds weight — a consideration in portable, wearable, or aviation-certified applications.

Common Mistakes Engineers Make with Bergquist Thermal Clad PCB

Based on the types of failures that show up in field returns and DFM reviews, these are the problems worth specifically avoiding:

1. Treating it like FR-4 in the Gerber package. Thermal Clad requires specific fabrication notes: base metal type and thickness, dielectric grade, copper weight, surface finish, and any selective dielectric removal areas. A generic FR-4 fab note set will result in the wrong board.

2. Ignoring the CTE mismatch between large SMD components and the aluminum base. Aluminum has a CTE of approximately 23 ppm/°C; ceramic capacitors and large IC packages are typically 6–10 ppm/°C. Large ceramic caps (2220 size and above) mounted on aluminum MCPCB boards are fatigue-failure candidates in thermal-cycling applications. Size down, use polymer caps, or add strain relief in the layout.

3. Using HPL for designs above 480V. The 38µm dielectric is not appropriate for high-voltage isolation. Refer to IEC 60664-1 for full creepage and clearance requirements and select HT-04503 or HT-07006 accordingly.

4. Forgetting that the base metal is thermally — but not always electrically — isolated. Some designs unintentionally create a ground connection to the chassis through the mounting hardware. If your base metal must be floating, use insulated standoffs.

5. Over-tightening assembly screws. Aluminum is softer than steel. Use torque specs from your hardware supplier and avoid steel screws without proper thread inserts in the board.

FAQs About Bergquist Thermal Clad PCB

Q1: What is the difference between Bergquist Thermal Clad and a standard aluminum PCB?

The defining difference is the dielectric layer. A standard aluminum-base PCB uses conventional epoxy prepreg (similar to FR-4) as the insulating layer between the circuit copper and the aluminum core. Bergquist Thermal Clad uses a proprietary polymer/ceramic compound that delivers 4–10× the thermal conductivity of standard prepreg. This translates directly into lower component operating temperatures for the same power dissipation level, or smaller/lighter board solutions for the same thermal budget.

Q2: Can Bergquist Thermal Clad PCB be used in multilayer designs?

Yes, with some caveats. Bergquist thermal clads aren’t only incorporated with metal base layers — these substrates can boost their function by replacing FR-4 in multilayer assemblies. A common two-layer configuration bonds a standard FR-4 or Thermal Clad circuit to the back of the Thermal Clad base using Bond-Ply adhesive. This gives you two routing layers while maintaining the metal-base thermal path. True buried via multilayer constructions are not standard for Thermal Clad.

Q3: Is Bergquist Thermal Clad RoHS and REACH compliant?

Yes. The HT series is RoHS compliant and environmentally green. The same applies across the HPL and MP families. All current Bergquist Thermal Clad products are lead-free solder process compatible and meet the material restriction requirements of RoHS 2 and REACH. Always request a current compliance declaration from your supplier, as formulations can be updated.

Q4: How does Bergquist Thermal Clad perform in thermal cycling tests?

Thermal Clad substrates are well-characterized for reliability. Bergquist PCBs are designed to handle the demands of electric vehicles or industrial machines, including fluctuating temperatures and vibrations. Bergquist PCBs meet these challenges with their high thermal conductivity, reliability, and rugged construction. For the most demanding thermal cycling requirements (e.g., AEC-Q200 automotive qualification), the LM (Low Modulus) dielectric variant is specifically formulated for improved fatigue resistance. For typical commercial or industrial applications (−40°C to +85°C, ~500 cycles), standard HT or MP materials perform well without special consideration.

Q5: Who makes Bergquist Thermal Clad PCBs now, and is it the same product?

The Bergquist Company was acquired by Henkel Corporation and integrated into their Electronic Materials division. The Bergquist TCLAD products are now manufactured and supplied through Henkel Corporation. TCLAD Inc. is a separate company that has developed its own IMS technology continuing in the same product space. The core dielectric technology principles remain consistent, but engineers specifying Bergquist materials by name should request the Henkel Bergquist branded product or verify equivalency testing if substituting a TCLAD Inc. product. The part number naming convention (HPL-03015, HT-04503, etc.) has been preserved through the Henkel era.

Final Thoughts

Bergquist Thermal Clad PCB has earned its reputation by solving a real engineering problem — getting heat out of dense, high-power electronics — with a material that is manufacturable at scale, certifiable for safety agencies, and well-understood by the PCB supply chain. The four dielectric families (HPL, HT, MP, LM) give engineers enough granularity to optimize for cost, thermal performance, or mechanical robustness depending on the application.

The real skill is knowing when to reach for it. For a 3W LED nightlight, it is overkill. For a 150W EV charging module expected to survive 10 years and 2,000 thermal cycles, it is the right tool. Getting that judgment right — and then executing the design with the correct grade, copper weight, and assembly process — is what separates a board that runs cool and reliable from one that comes back in a warranty claim.

Use the datasheets and design guides linked above, run the thermal resistance calculations, and remember that the dielectric grade selection is one of the most leverage-heavy decisions in the entire design. Get that right, and the rest tends to follow.

Have a design challenge with Bergquist Thermal Clad PCB materials? Drop your questions in the comments or reach out to a qualified PCB manufacturer who can help with material selection and DFM review.

The post The Complete Guide to Bergquist Thermal Clad PCB Materials [2025] appeared first on RayPCB.

If you’ve spent any time specifying IMS boards for LED or power electronics designs, you’ve almost certainly hit the same wall of questions that every engineer hits the first time through: What’s the actual difference between HT and HPL? Can this material handle a standard lead-free reflow profile? Do I really need a soldermask? What happened to Bergquist after Henkel acquired them?

This Bergquist thermal clad FAQ compiles the 25 questions that come up most often — from materials engineers evaluating the technology for the first time to experienced designers troubleshooting a production issue. Answers are drawn directly from the TCLAD selection guide, published datasheets, and real fabrication experience. No filler, no padding — just the answers.

Section 1: Material and Technology Fundamentals

Q1. What exactly is Bergquist Thermal Clad, and how does it differ from a standard aluminum PCB?

Thermal Clad is an Insulated Metal Substrate (IMS) technology built around a proprietary polymer-ceramic dielectric layer bonded between a copper circuit layer on top and an aluminum (or copper) base beneath. The technology of Thermal Clad resides in the dielectric — a polymer chosen for its electrical isolation properties and ability to resist thermal aging, combined with a ceramic filler that enhances thermal conductivity while maintaining high dielectric strength.

The critical difference from generic aluminum PCBs is that standard aluminum boards use conventional prepreg as the dielectric, which achieves 1.0–2.0 W/m·K thermal conductivity. The TCLAD dielectric achieves up to 7.5 W/m·K in the HPL-03015 grade — a 4× to 7× improvement. That performance gap translates directly to lower LED junction temperatures, longer component lifetime, and the ability to run higher watt density without exceeding thermal limits.

Q2. What does the part number mean — for example, HPL-03015 or HT-04503?

The part number encodes three pieces of information:

So HT-04503 means: High Temperature dielectric, 0.45 °C·in²/W thermal resistance, 3 mils (76 µm) thick. Once you internalize this convention, you can decode any Thermal Clad part number without opening a datasheet.

Q3. What dielectric families are available in the Thermal Clad lineup?

The main commercial families are: HPL (High Power Lighting) optimized for maximum thermal performance at low voltage, HT (High Temperature) offering a balance of thermal performance and high dielectric breakdown up to 6–11 kV depending on thickness, MP (Multi-Purpose) for general purpose cost-sensitive designs, and LM (Low Modulus) for formable applications where the substrate needs to be mechanically shaped after assembly. HT-04503 and MP-06503 are the most widely stocked at fabricators. HPL-03015 requires more lead time at most shops.

Q4. Is Bergquist still the manufacturer, or has the brand changed?

The short version: the material now comes from TCLAD Inc. The Bergquist Company originally developed Thermal Clad, then Bergquist was acquired by Henkel in 2014. In 2021, Polytronics Technology Corp. acquired the Thermal Clad product line from Henkel and formed TCLAD Inc., a Delaware corporation. Manufacturing remains at the 100,000 sq. ft. Innovation Center in Prescott, Wisconsin, with operations also in Frankfurt, Germany and Hsinchu City, Taiwan. All original personnel and part numbers carried over. “Bergquist thermal clad” remains the common industry reference term for the technology, but the official brand is now TCLAD.

Q5. What is the thermal conductivity of Bergquist Thermal Clad, and how is it measured?

Thermal conductivity varies by dielectric grade. The table below summarizes the main grades:

Measurement uses two ASTM test methods: ASTM D5470 (steady-state method, direct derived value) and ASTM E1461 (Laser Flash diffusivity, from which conductivity is calculated). Both are referenced in TCLAD datasheets. It’s worth noting that the two methods can yield slightly different values due to their differing assumptions, which is why TCLAD datasheets specify the test method alongside the conductivity figure.

Q6. What does “unit thermal resistance” mean versus “thermal resistance” on the datasheet?

These are related but not interchangeable. Unit thermal resistance (°C·in²/W) is a material property normalized per unit area — use this to calculate the actual resistance for your specific component footprint. Thermal resistance (°C/W) in most TCLAD datasheets refers to the resistance measured across a 1 in² test area.

The working formula: R_dielectric (°C/W) = Unit Thermal Resistance (°C·in²/W) ÷ Component Pad Area (in²)

For a 5mm × 5mm LED pad (0.025 in²) on HPL-03015: R = 0.02 ÷ 0.025 = 0.8 °C/W. On HT-04503: R = 0.05 ÷ 0.025 = 2.0 °C/W. That 1.2 °C/W difference at 3W dissipation means 3.6°C hotter junction temperature on HT vs HPL — significant when you’re managing LED lifetime.

Q7. What base metal options are available, and when would you use copper instead of aluminum?

Aluminum base (1100 alloy or equivalent) is standard and covers the vast majority of LED and power electronics applications. It’s lightweight, cost-effective, and thermally adequate for most designs. Copper base is available and offers higher thermal conductivity and better CTE matching to ceramic and bare die assemblies — but it comes at significantly higher cost. Per the TCLAD selection guide, 0.125″ (3.18mm) aluminum base is equivalent in cost to 0.040″ (1.0mm) copper base. Choose copper base when you need maximum lateral heat spreading, direct die attachment, or CTE compatibility with ceramic substrates. For most LED applications, aluminum is the right call.

Section 2: Design and Layout Questions

Q8. What are the key circuit design guidelines for Thermal Clad boards?

The TCLAD selection guide publishes recommended circuit design limits for standard fabrication:

Note that use of a soldermask is mandatory on Thermal Clad — this isn’t optional. It’s required for UL compliance and for maintaining adequate voltage isolation at conductor edges.

Q9. Do you need thermal vias on a Thermal Clad board?

Generally no, and in most single-layer IMS designs they can actually be counterproductive. On IMS PCBs, thermal vias can be problematic since the drill penetrates through the aluminum base and isolation must be maintained through the via annular ring. The aluminum itself handles heat spreading far better than an array of via copper can. The whole point of an IMS board is that the base metal spreads heat laterally to the heatsink contact area — vias in FR-4 are a workaround for the absence of that spreading. Don’t add thermal vias to a Thermal Clad board unless there is a specific electrical reason (not thermal) to connect layers.

Q10. Can Thermal Clad boards be used in multi-layer configurations?

Yes, but it’s a specialty application. TCLAD describes configurations using Bergquist dielectrics bonded to a metal base with FR-4 type circuits or Thermal Clad circuits, depending on thermal requirements and cost objectives. Multi-layer Thermal Clad assemblies are less common than single-layer designs and require more specialized fabrication. For most LED and power supply designs, single-layer IMS is adequate and significantly simpler to fabricate and inspect. Contact TCLAD directly for guidance if your application genuinely requires a multi-layer IMS stack.

Q11. What is the minimum conductor-to-board-edge distance on Thermal Clad?

The standard recommendation from the TCLAD selection guide is 0.040″ (1.0mm) minimum from any conductor to the board edge. This accounts for both electrical isolation and the mechanical stress that occurs at the routed edge. If you’re using edge connectors, a 45° chamfer at the connector edge is recommended — and the minimum conductor-to-edge distance must still be maintained along the chamfered section. This is one of those design details that often gets overlooked in the Gerber review and causes rework on first prototypes.

Q12. What copper weight should I specify for an LED board?

For most LED designs, 1 oz copper (35 µm) is the standard and most cost-effective choice. Thermal Clad trace interconnects can actually carry higher currents than equivalent FR-4 traces of the same width because the base metal dissipates the I²R heating more effectively. Where you need higher current-carrying capacity — motor drive bus bars, high-current LED strings — 2 oz or 3 oz copper is available. Heavy copper requires modified etching chemistry and longer etch times, which your fab house needs to account for in DFM review. Specifying 2 oz on a board that only needs 1 oz adds cost without any thermal benefit, so run the trace width calculation from IPC-2221 first.

Section 3: Assembly and Soldering

Q13. Is Bergquist Thermal Clad compatible with standard lead-free reflow profiles?

Yes, with some attention to profile management. TCLAD boards are compatible with standard SAC305 lead-free reflow — peak temperatures in the 240–260°C range for 30–60 seconds are within the dielectric’s rating. The TCLAD selection guide notes the material is rated at 325°C/60 seconds for eutectic gold/tin solders, so standard lead-free profiles are well within limits. The key consideration for IMS reflow is that the aluminum base has significantly higher thermal mass than FR-4, which means your board takes longer to reach peak temperature and your oven profile needs to account for that. Profile validation on the actual board with thermocouples is essential, not optional.

Q14. What solder thickness is recommended for Thermal Clad assemblies?

The TCLAD selection guide specifies a minimum solder thickness of 0.004″ (100 µm) after reflow. This is thicker than many engineers default to for SMT. The reason is that Thermal Clad’s aluminum base has a different CTE than the component packages, and sufficient solder thickness provides compliance to absorb that differential expansion over thermal cycles. Insufficient solder thickness is one of the most common root causes of premature solder joint failure on IMS boards. Use metal stencils for solder paste application — dispensing is acceptable for secondary operations but harder to control for consistent paste volume.

Q15. What surface finishes are compatible with Thermal Clad, and which is recommended?

The TCLAD selection guide lists HASL (SnPb or lead-free), OSP, and FST (Flow Solderable Tin) as compatible finishes. In practice for LED applications, ENIG is the most commonly specified surface finish because it provides flat, coplanar pads with consistent standoff height — critical for repeatable solder joint thickness and thermal resistance at the LED interface. OSP has a 3–6 month shelf life limitation, which can be a logistics problem for boards that sit in WIP inventory before assembly. HASL is acceptable for non-critical pads and offers better shelf life than OSP. All TCLAD dielectrics are confirmed lead-free solder compatible and RoHS compliant.

Q16. Can Thermal Clad be wave soldered?

Wave soldering of IMS boards is not commonly practiced and not generally recommended for fine-pitch SMT designs. The thermal mass of the aluminum base creates uneven heating across the board during wave solder contact, and the single-layer nature of most IMS boards means all components are on one side anyway — making wave solder unnecessary for most designs. Where through-hole components must be soldered on a Thermal Clad board (pin headers, connectors), selective soldering or hand soldering is typically specified.

Q17. How should I handle and store bare Thermal Clad boards before assembly?

Per the TCLAD technical data sheets, optimal storage is at 5–25°C with a 12-month shelf life for the laminate in unopened containers. Bare fabricated boards with ENIG or HASL finish have similar storage requirements to standard PCBs: low humidity, no ESD sensitive concerns for the board itself, but moisture-sensitive components should be handled per J-STD-033. Aluminum surfaces are susceptible to oxidation if exposed — keep boards in sealed moisture barrier bags if not assembling promptly after receipt.

Section 4: Electrical and Isolation Properties

Q18. What dielectric breakdown voltage should I expect?

Breakdown voltage varies significantly by dielectric family and thickness. This is one of the most important selection criteria for any design with mains voltage or significant working voltage:

For applications expecting voltage over 480V AC, TCLAD recommends a dielectric thickness greater than 0.003″ (76 µm). These are breakdown values, not working voltage ratings — apply your appropriate safety factor. Circuit design is the most important consideration for determining safety agency compliance; the dielectric breakdown value alone does not guarantee UL or CE compliance.

Q19. What does the UL RTI rating mean, and why does it matter?

UL RTI (Relative Thermal Index) defines the maximum long-term continuous operating temperature at which the dielectric retains at least 50% of its original electrical or mechanical properties. Many Thermal Clad products have UL ratings up to 45% higher than their glass transition temperature (Tg) — this is intentional and reflects the material’s robust long-term performance. For HT-04503, the UL RTI is 140/140°C (Electrical/Mechanical). Tg for the dielectric is nominally around 150°C. This distinction matters for product qualification under UL 746B and for thermal lifetime calculations in LED luminaire certification.

Q20. Do I need to proof-test every board after fabrication?

For production boards, yes — and the test method requires care. Due to the capacitive nature of the IMS construction, it is necessary to control the ramp-up of voltage during proof testing to avoid nuisance tripping of failure detection circuits and to prevent premature surface arcing. TCLAD documentation recommends a specific ramp rate rather than a step-apply approach. Any micro-fractures, delaminations, or micro-voids in the dielectric will break down or respond as a short under test — which is exactly what you want to detect in production, not in the field. After DC testing, the operator must verify the board is fully discharged before removing from the test fixture. This is a safety step, not just a quality step.

Section 5: Application-Specific and Supplier Questions

Q21. Is Bergquist Thermal Clad suitable for automotive applications?

Yes, and it’s widely used in automotive LED headlamp systems, EV power modules, and DC-DC converters. TCLAD’s advanced thermal management solutions are trusted in the EV sector to prevent overheating of batteries, power electronics, and control units, ensuring safe, reliable operation and charging. For direct automotive supply chain applications, your fabricator should hold IATF 16949 certification in addition to ISO 9001. The HT-04503 dielectric with its 6 kV breakdown rating and 140°C UL RTI is the most commonly specified grade for automotive IMS applications. For automotive applications under 480V bus voltages, HT-04503 provides adequate isolation margin.

Q22. Can Thermal Clad replace ceramic substrates?

In many applications, yes. Thermal Clad can replace large-area ceramic substrates and can be used as a mechanically durable support for ceramic spacers or direct bonded copper subassemblies. The copper circuit layer of Thermal Clad has more current-carrying capability than thick-film on ceramic, and it’s far more mechanically robust than DBC (Direct Bonded Copper) ceramic during handling and assembly. The trade-off is thermal conductivity: alumina ceramic runs 20–25 W/m·K and AlN runs 150–180 W/m·K — substantially higher than even the best TCLAD dielectric. For applications where the highest possible thermal conductivity is the primary constraint (high-density power semiconductor modules, for example), ceramic may still be necessary. For most LED and moderate-power electronics applications, TCLAD offers better mechanical robustness, comparable or better electrical isolation, and simpler fabrication than ceramic at lower cost.

Q23. How do I verify that my PCB fabricator is using genuine TCLAD material?

Request a material certificate (mill cert) with each production lot. This document should reference the TCLAD Inc. part number, lot number, and date of manufacture. A legitimate IMS fabricator using genuine TCLAD laminate will have this documentation available without hesitation. As a secondary check, you can request thermal conductivity test data from a sample of your production lot — genuine HPL-03015 should measure close to 7.5 W/m·K; generic substitutes typically measure 1.0–2.0 W/m·K, a difference that’s clearly detectable with standard ASTM D5470 testing. The price gap between genuine TCLAD and generic aluminum laminate is real — if your quote is suspiciously cheap for an HPL board, that’s worth investigating before committing to production.

For a broader look at IMS board sourcing options including alternative materials, engineers can also review Bergquist PCB options and alternatives at RayPCB, which covers material selection considerations from a fabrication perspective.

Q24. What certifications should a qualified Bergquist Thermal Clad fabricator hold?

The minimum credible certification set for an IMS PCB fabricator includes ISO 9001:2015 for quality management, UL 796 facility recognition for boards going into UL-listed products, and IPC-2221/IPC-A-600 for design and inspection compliance. The TCLAD selection guide states that Bergquist lab facilities are UL certified and manufacturing facilities are ISO certified. For automotive applications, IATF 16949 is mandatory in the automotive Tier supply chain. If your design is going into a CE-marked product, confirm the fab’s process documentation supports the Annex II technical file requirements for relevant directives.

Q25. What has changed in the Thermal Clad product line since the TCLAD Inc. acquisition?

From an engineer’s day-to-day perspective, not much has changed that affects design decisions. The part numbers are the same, the dielectric chemistry is unchanged, and the manufacturing facility in Prescott, Wisconsin continues to produce the same material families. TCLAD continues to innovate from its vertically integrated manufacturing center, delivering thermal management solutions for high-power density applications in LED lighting, automotive EV systems, aerospace and defense, industrial power, and power semiconductors. What has changed at the supply chain level: the company name on purchase orders and certificates of conformance is now TCLAD Inc. rather than Henkel/Bergquist. Authorized distributors including DigiKey continue to stock TCLAD laminate. If you’re working with an overseas fabricator who still refers to the material as “Henkel Bergquist,” that’s not incorrect historically — but your mill cert should now reference TCLAD Inc. as manufacturer.

Quick Reference: Dielectric Selection Summary

Useful Resources for Bergquist Thermal Clad Engineering

Summary

The 25 questions above cover the majority of what engineers actually need to know when evaluating, designing with, or troubleshooting Bergquist Thermal Clad IMS boards. The technology is mature and well-documented — the TCLAD selection guide alone answers most fabrication and design questions in detail. The most common mistakes in practice are: picking the wrong dielectric grade for the voltage requirements, not accounting for aluminum thermal mass in reflow profiling, specifying insufficient solder thickness for thermal cycling reliability, and failing to verify material traceability on overseas orders.

If you have a question not covered here, TCLAD Inc.’s technical team in Prescott, Wisconsin is actively supporting the product line post-acquisition and is the authoritative source for application-specific guidance.

Suggested Meta Description:

Get straight answers to 25 of the most common Bergquist thermal clad FAQ questions — from dielectric grades and thermal resistance to soldering, voltage ratings, and finding genuine TCLAD suppliers. Engineer-written, datasheet-backed. (157 characters)

The post Bergquist Thermal Clad PCB FAQ: 25 Most Asked Questions Answered appeared first on RayPCB.

If you’ve ever opened a Bergquist thermal clad datasheet and wondered which numbers actually matter for your LED or power electronics design, you’re not alone. The datasheets pack in a lot of electrical, thermal, and mechanical specs—and not all of them carry equal weight depending on your application. This guide walks through each section from a working PCB engineer’s perspective, covers how to use those numbers in real thermal resistance calculations, compares the two most commonly specified dielectrics (HPL-03015 vs HT-04503), and spells out the layout rules you need to actually build a reliable IMS board.

What Is Bergquist Thermal Clad (and Why Does It Matter)?

Bergquist Thermal Clad is a family of Insulated Metal Substrate (IMS) PCBs developed specifically for high-watt-density surface-mount applications. The stackup is simple—copper circuit layer on top, a proprietary polymer-ceramic dielectric in the middle, and an aluminum (or copper) base beneath—but the technology in that dielectric layer is what separates it from generic aluminum-core boards.

Thermal Clad MCPCBs minimize thermal impedance and conduct heat more effectively than standard printed wiring boards, and they are more mechanically robust than thick-film ceramic and direct bond copper construction. For LED lighting and power conversion applications, this translates directly to lower junction temperatures, longer component lifetimes, and the ability to run more forward current per LED without cooking the package.

The low thermal impedance of the Thermal Clad dielectric out-performs other insulators for power components, allowing for cooler operation. Thermal Clad keeps assemblies cool by eliminating thermal interfaces and using thermally efficient solder joints.

Now that’s the marketing pitch. Let’s talk about how to actually use the datasheet.

The Structure of a Bergquist Thermal Clad Datasheet

Every Bergquist Thermal Clad datasheet (now published under Henkel, which acquired Bergquist) follows the same basic architecture. Understanding what each section means before you start comparing part numbers will save you hours of back-and-forth with your fab house.

Dielectric Identification and Product Series

The part number itself encodes critical information. Take HPL-03015 as an example:

• HPL = High Power Lighting dielectric family
• 030 = Thermal resistance in °C·in²/W × 100 (so 0.30 °C·in²/W)
• 15 = Dielectric thickness in tenths of mils (so 1.5 mils / 38 µm)

The same logic applies to HT-04503: HT (High Temperature), 045 = 0.45 °C·in²/W, 03 = 3 mils / 76 µm thick. Once you internalize this convention, you can decode any Thermal Clad part number at a glance.

Thermal Performance Parameters — The Numbers That Drive Your Design

This is the section most engineers should spend the most time on. There are three closely related values that often get confused:

Thermal Conductivity (W/m·K) — A material property, independent of thickness. Higher is better. Think of this as how efficiently the dielectric moves heat per unit of thickness.

Thermal Resistance (°C·in²/W or °C·W⁻¹) — This is thickness-dependent and tells you the temperature rise per watt per unit area. This is what you’ll plug into your junction-to-ambient thermal chain calculation.

Thermal Impedance (°C/W) — For a given test area (typically 1 in²), this is the total resistance of the complete laminate stack under test conditions.

For the HPL-03015, the dielectric thickness is 1.5 mil / 38 µm, thermal resistance is 0.30°C/W, and the unit thermal resistance is 0.02°C·in²/W. For HT-04503, thickness is 3 mil / 76 µm, thermal resistance is 0.45°C/W, and unit thermal resistance is 0.05°C·in²/W.

Dielectric Strength (kV)

This tells you the voltage the dielectric can withstand before breakdown. For LED luminaire designs running on mains voltage (120–240V AC), you need meaningful headroom above your working voltage. HT-04503 carries a breakdown voltage of 6.0 kV for LED applications. This is important not just for safety isolation, but for your creepage and clearance calculations in CE/UL-listed luminaire designs.

Operating Temperature and Glass Transition (Tg)

Tg is the temperature at which the dielectric shifts from a rigid, glassy state to a softer, rubbery state. Exceeding Tg repeatedly accelerates delamination and CTE-induced solder joint fatigue. The HPL-03015 dielectric at 0.0015″ (38µm) has a glass transition of 185°C. That’s an unusually high Tg for this class of material and is one of the reasons HPL-03015 is preferred for high-junction-temperature LED packages.

Copper Weight / Circuit Layer

Copper foil is NOT measured for thickness as a control method—instead it is certified to an area weight requirement per IPC-4562. The nominal thickness for 1 oz copper is 0.0014″ / 35 µm. Most LED IMS designs use 1 oz copper. If you’re running high current traces (motor drivers, DC-DC converters), consider 2 oz or 3 oz—but check your fab’s DFM rules first, as heavy copper requires modified etching chemistry.

UL RTI (Relative Thermal Index)

The RTI values (Electrical / Mechanical) define the long-term maximum operating temperature the material can sustain while retaining at least 50% of its original electrical or mechanical properties. HT-04503 carries UL RTI values of 140/140°C. This matters for lifetime assessments and product qualification under UL 746B.

Bergquist Dielectric Comparison Table

Here’s a side-by-side of the most commonly specified Thermal Clad dielectrics from the selection guide:

Source: Bergquist Thermal Clad Selection Guide (Henkel/Bergquist)

HPL-03015 vs HT-04503: Which One Should You Pick?

This is the question that comes up in almost every high-power LED design review. Here’s how to think through it practically:

Choose HPL-03015 When:

HPL is a dielectric specifically formulated for high power lighting LED applications with demanding thermal performance requirements. This thin dielectric at 0.0015″ (38 µm) has an ability to withstand high temperatures with a glass transition of 185°C and phenomenal thermal performance of 0.30°C/W. It is optimized for COB (Chip-on-Board) and high-lumen-density arrays where getting heat out fast is the primary constraint, and operating voltages are relatively low (under 60V DC in most SSL designs). With a unit thermal resistance of only 0.02°C·in²/W and thermal conductivity of 7.5 W/m·K, it’s the best-performing dielectric in the Thermal Clad lineup.

The trade-off: its dielectric strength is only 2.5 kV. That’s fine for low-voltage LED drivers, but not suitable for mains-isolated designs without additional creepage management.

Choose HT-04503 When:

HT-04503 is specifically designed for applications that involve high-power systems with significant heat dissipation requirements. Its ability to perform in high-temperature conditions makes it a popular choice for industries like automotive, telecommunications, and high-frequency circuits. The 6 kV breakdown rating gives you much better margin for line-voltage isolation, and the 2.2 W/m·K conductivity is still a significant improvement over FR-4.

If you’re designing an LED driver board with mains-referenced components mounted on the same substrate, or an automotive LED headlamp controller where 48V bus voltages are common, HT-04503 is the safer choice.

Decision Summary

Thermal Resistance Calculations for IMS PCB Design

Reading the datasheet is one thing. Actually using those numbers in a design calculation is where engineers often stumble. Here’s a practical walkthrough.

The Thermal Resistance Chain

For an LED mounted on an IMS board attached to a heatsink, the thermal resistance from junction to ambient looks like this:

Rθ(j-a) = Rθ(j-c) + Rθ(c-board) + Rθ(dielectric) + Rθ(base-metal) + Rθ(TIM) + Rθ(heatsink)

In practice, the base metal (aluminum) resistance is negligible — aluminum at 1.5mm thick contributes roughly 0.006°C/W per cm². The dominant resistance in an IMS stack is usually the dielectric layer, followed by the TIM between the IMS base and heatsink.

Calculating Dielectric Thermal Resistance

The formula is straightforward:

R_dielectric = (Unit Thermal Resistance) / (Component Footprint Area)

For a 3W LED with a 5mm × 5mm (0.025 in²) thermal pad on HPL-03015:

R_dielectric = 0.02 °C·in²/W ÷ 0.025 in² = 0.8 °C/W

The same LED on HT-04503:

R_dielectric = 0.05 °C·in²/W ÷ 0.025 in² = 2.0 °C/W

At 3W dissipation, that’s a 1.8W × (2.0 − 0.8) = 2.16°C difference in junction temperature from dielectric selection alone. Across a string of 20 LEDs running warm, that gap compounds quickly.

Example: Full Thermal Budget for an LED Street Light Module

At 3W dissipation: ΔT = 3W × 7.9 °C/W = ~23.7°C rise above ambient. If ambient is 45°C (outdoor luminaire), junction temperature is approximately 69°C — well within most LED ratings.

Compared to a 1.60mm FR4 PCB, an IMS PCB with 0.15mm thermal prepreg can have a thermal resistance more than 100 times lower. That’s the fundamental engineering argument for IMS in LED applications.

IMS PCB Layout Rules for LED Thermal Management

The datasheet numbers only matter if your layout lets the heat actually flow. Here are the design rules that matter most in practice.

Copper Pour and Pad Design

Use large copper pours directly under LED thermal pads. The copper spreads heat laterally before it crosses the dielectric, reducing the effective thermal resistance. Place high-power parts above the best thermal path to the base, avoiding edges and cutouts. Cluster heat sources to share large pads and simplify localized cooling.

For individual LED packages, extend the thermal pad in copper to at least 2× the component pad area where routing permits. Avoid routing signal traces through or near the main thermal pour—they create gaps that interrupt lateral heat spreading.

Component Spacing

Maintain at least 2–3mm spacing between high-power components to avoid thermal interference. On a dense COB-replacement array, this may not always be achievable, but it’s the starting point. When components must be packed tightly, ensure copper pours are continuous between them so heat can spread to the entire base metal area.

Via Design on IMS

Unlike FR-4 designs where thermal vias are a standard heat path, IMS boards require careful thought. On IMS PCBs, thermal vias can be counterproductive since you have to drill through large parts of the conducting aluminum. Thermal insulation may be insufficient in cases like that—it is better to go for IMS PCBs without thermal vias because the aluminum transfers the heat within the carrier. In most single-layer IMS designs, you simply don’t need them; the aluminum base does the spreading job.

Solder Mask and Surface Finish

For LED applications, use a white solder mask where possible—it significantly improves optical reflectivity, which matters for luminaire efficiency. ENIG (Electroless Nickel Immersion Gold) surface finish is preferred for LED footprints because it provides flat, solderable pads with repeatable standoff heights. HASL (Hot Air Solder Leveling) is acceptable for cost-sensitive designs but can result in uneven pad topography.

Trace Width and Conductor Design

Standard IMS design rules specify a minimum conductor width and spacing of ≥100 µm, copper thickness from ½ oz (17.5 µm) to 4 oz (140 µm), and dielectric strength of 6 kV AC.

For current-carrying traces on IMS, you can generally use narrower traces than FR-4 equivalent designs because the aluminum base acts as a heat spreader. However, keep high-current bus traces wide (use IPC-2221 as your baseline), and run them away from the edge of the board where the dielectric can be mechanically stressed during depaneling.

Edge-to-Conductor Clearance

Maintain a minimum of 1mm from any conductor to the board edge for standard IMS. If your design uses a 45° chamfer at edge connectors (which Bergquist recommends in the selection guide), verify this clearance is maintained across the chamfered section. Routing cuts through the aluminum substrate using CNC require carbide or diamond-coated tooling—brief your fab house on this if they’re not experienced with IMS.

Useful Resources for Bergquist Thermal Clad Datasheet Work

These are the documents and tools worth bookmarking when working with Thermal Clad IMS:

Frequently Asked Questions

Q1: The datasheet lists thermal resistance in both °C·in²/W and °C/W. Which one do I use?

Use °C·in²/W (unit thermal resistance) when you want to calculate the actual resistance for a specific component footprint area — just divide by your pad area in in². Use °C/W (already normalized to a 1 in² test area in most Bergquist datasheets) as a quick material comparison metric. They’re related by: Thermal Resistance (°C/W) = Unit Thermal Resistance (°C·in²/W) × (1 in² / actual area in²). Don’t mix units when you’re building a thermal chain calculation.

Q2: Can I use Bergquist Thermal Clad with double-sided SMT assembly?

Single-layer IMS is the standard configuration, and the vast majority of LED board designs use it. True double-sided IMS (components on both faces) is possible but requires specialized fabrication and careful attention to solder reflow sequence. For most designs requiring both sides, it’s more practical to use a hybrid approach — IMS on the LED side and FR-4 for a control circuit board, bonded or mounted separately.

Q3: My LED vendor’s datasheet shows Rθ(c-b) (case to board) resistance. Does that replace the IMS dielectric resistance?

No. Rθ(c-b) is the thermal resistance from the LED package case to the top surface of the PCB, and it’s measured under a specific test condition (usually a defined copper area). The IMS dielectric resistance is a separate, additional resistance from the top of the copper layer through the dielectric to the aluminum base. Both are in series in your thermal chain — you add them together.

Q4: How do I verify the thermal performance of my IMS board after assembly?

The most common method is infrared thermography under controlled power conditions. Apply a known power level to the LED array, let it reach steady state (typically 5–10 minutes), and use an IR camera to map the temperature distribution on the component surface. Compare your peak temperatures against your thermal model. If your junction temperature is running significantly hotter than predicted, look first at the TIM interface between the IMS base and heatsink — it’s usually the culprit.

Q5: Is Bergquist Thermal Clad still available now that Henkel acquired Bergquist?

Yes. The technology continues under the TCLAD brand name, with manufacturing and global innovation based in Prescott, Wisconsin, and regional operations in Europe and Taiwan. The Henkel product portal carries the same dielectric families under the Bergquist brand, and part numbers like HPL-03015 and HT-04503 remain active. Always confirm material availability with your PCB fabricator, since lead times for specialty IMS materials can vary from standard FR-4 runs.

Summary

Reading a Bergquist thermal clad datasheet comes down to four things: understanding the thermal resistance chain, knowing the difference between unit thermal resistance and bulk thermal conductivity, picking the right dielectric for your voltage and junction temperature requirements, and designing your copper layout to let that low dielectric resistance actually do its job.

For pure LED lighting applications below 60V, HPL-03015 gives you the best junction-to-base thermal performance available in the Thermal Clad family. When mains isolation or higher breakdown voltage is required, HT-04503 is the workhorse choice. Both materials are mature, well-characterized, and supported by a global supply chain — which matters as much as the datasheet numbers when you’re running production.

Meta Description Suggestion:

Learn how to read a Bergquist thermal clad datasheet like an engineer — thermal resistance calculations, HPL-03015 vs HT-04503 comparison tables, IMS PCB layout rules, and FAQs for LED and power electronics designers. (155 characters)

The post How to Read a Bergquist Thermal Clad Datasheet: Engineer’s Guide appeared first on RayPCB.

Picking the wrong Bergquist dielectric is one of those decisions that looks fine on paper until the field return report lands on your desk three months after launch. Junction temperatures higher than modeled. Delamination after 200 thermal cycles. A Tg margin that turned out to be thinner than expected. None of it catastrophic on its own, but all of it traceable back to the material selection call made early in the design.

This guide is written for engineers doing Bergquist PCB material selection for real designs — not someone browsing datasheets out of curiosity. It covers the Thermal Clad dielectric family in depth, the key decision variables, base metal choices, design considerations that affect reliability, and a practical selection framework you can actually use. By the end, you should be able to pick a dielectric with confidence rather than defaulting to whatever the previous revision used.

Why Bergquist Thermal Clad Exists and What Problem It Solves

The Bergquist Thermal Clad PCB technology is engineered to improve the efficiency of heat dissipation from electronic components, particularly in devices that generate a significant amount of heat. The fundamental issue it solves is simple: standard FR-4 is a thermal insulator. Its thermal conductivity sits at roughly 0.2–0.3 W/m-K, which means it actively works against you when power-dense components need to dump heat through the board.

Thermal Clad flips this relationship. The dielectric is a proprietary polymer/ceramic blend — glass-free, unlike FR-4 prepreg — that bonds a copper circuit layer to a metal base (typically aluminum). These substrates minimize thermal impedance and conduct heat more effectively and efficiently than standard printed wiring boards. They are more mechanically robust than thick-film ceramics and direct bond copper constructions that are often used in these applications.

The copper substrate offers 390 W/mK conductivity while aluminum substrate offers 205 W/mK conductivity — both significantly higher than typical FR-4 boards. The key point here is that the metal base is the primary heat spreader; the dielectric’s job is to electrically isolate the copper circuit from the base while transferring heat as efficiently as its chemistry allows. Every dielectric family Bergquist offers makes a different trade-off between thermal performance, temperature tolerance, and cost.

The Bergquist Thermal Clad Dielectric Families Explained

Bergquist organizes its Thermal Clad dielectrics into named families. Each family has its own polymer chemistry, thermal performance tier, and target application environment. Getting this choice right is the foundation of good Bergquist PCB material selection.

LTI — Low Temperature Insulator

LTI is the entry point of the Thermal Clad family. It’s a moderate-performance dielectric aimed at applications where the board won’t see sustained high temperatures and budget is a real constraint. Thermal conductivity sits at approximately 1.5 W/m-K with a Tg around 130°C. Consumer electronics, standard LED drivers, audio amplifier output stages, and general-purpose power supply boards are its natural habitat. If your steady-state board temperature comfortably stays below 100°C and thermal cycling isn’t extreme, LTI is the economically sound choice.

MP — Multi-Purpose

The MP dielectric steps up the thermal conductivity to approximately 2.4 W/m-K, making it the most versatile option in the range. When choosing dielectric materials, you have to consider thermal conductivity: this is an important factor you should not overlook. The Bergquist Thermal Clad’s thermal conductivity determines thermal performance — this is especially important when interfacial area and resistance are considered. MP covers most general-purpose power electronics, mid-range LED lighting, and motor drive boards where LTI’s thermal conductivity is insufficient but HT’s temperature capability is more than you need.

HT — High Temperature

The HT dielectric is where Bergquist’s chemistry gets serious. The HT variant delivers a thermal conductivity of 4.1 W/m-K and a thermal resistance of 0.05°C·in²/W. It is, as its name states, resistant to degradation from high temperature exposure and features high dielectric breakdown characteristics. This dielectric is proven in applications such as LED, power supply, motor drives, and solid state relays. HT dielectrics are U.L. solder rated at 325°C/60 seconds, which enables Eutectic Gold/Tin solders and wire bonding with gold wire — options that aren’t available with the lower-tier dielectrics.

HPL — High Power Lighting

HPL is a specialist dielectric, not a general-purpose option. HPL is a dielectric specifically formulated for high power lighting LED applications with demanding thermal performance requirements. This thin dielectric at 0.0015″ (38 µm) has an ability to withstand high temperatures with a glass transition of 185°C, thermal conductivity of 3.0 W/m-K, and thermal impedance of 0.30°C/W. The thin dielectric layer is the enabling factor — less material between the LED junction and the aluminum base means dramatically lower thermal resistance, which translates directly to higher lumen output and longer LED lifespan at the same drive current.

CML — Ceramic-Metal Laminate

CML is the high-end outlier in the Bergquist dielectric lineup. It uses a glass carrier (the only Bergquist dielectric that does, for handling purposes) and is targeted at applications needing maximum thermal performance combined with the ability to replace ceramic substrates. It’s the option you look at when designing thick-film ceramic replacements in motor inverters, high-frequency switching circuits, and bare-die mounting applications.

Full Bergquist Dielectric Comparison Table

Understanding the full picture of Bergquist PCB material selection requires comparing the key parameters across dielectric families side by side.

The Naming Convention Decoded

Once you understand how Bergquist names its products, reading a part number becomes straightforward. Take HT-04503 as an example: “HT” is the dielectric family. “045” is the approximate total laminate thickness in mils. “03” is the dielectric layer thickness in mils (3 mil = ~76 µm). So LTI-04503 is a Low Temperature Insulator with a 3-mil dielectric, and MP-06503 is a Multi-Purpose dielectric with a 3-mil dielectric on a 65-mil total laminate.

The dielectric thickness matters significantly: for applications with an expected voltage over 480 Volts AC, Bergquist recommends a dielectric thickness greater than 0.003″ (75 µm). If your application is above that threshold, either choose a product with a thicker dielectric or apply appropriate creepage and clearance margin in your PCB layout per IEC 60664-1.

Five Key Decision Variables for Bergquist PCB Material Selection

1. Operating Temperature and Tg Margin

Your dielectric’s glass transition temperature isn’t just a spec to note — it’s the upper bound of predictable behaviour. The temperature of the operating environment determines a lot: it determines not only the peel strength and CTE, but also the storage modulus. When there is an increase in temperature, the storage modulus decreases. Running a dielectric consistently near its Tg degrades bond strength, increases CTE, and erodes electrical properties over time. The practical rule is to target at least 20–30°C of Tg headroom above your sustained maximum junction-area temperature.

2. Thermal Conductivity vs. Thermal Resistance

These two parameters are related but distinct. Thermal impedance measures how temperature declines across each watt’s stack-up. Lower thermal impedance indicates that more heat moves out of the components. Thermal conductivity is a material property; thermal resistance is a system-level value that depends on both conductivity and the dielectric layer thickness. A thinner dielectric from a lower-conductivity family can outperform a thicker dielectric from a higher-conductivity family in thermal resistance terms. Always compare thermal resistance (°C·in²/W or °C·cm²/W), not just conductivity, when evaluating options.

3. Dielectric Breakdown and Voltage Rating

For any design with significant AC or DC bus voltages, the dielectric breakdown spec is non-negotiable. The standard 3-mil (76 µm) Thermal Clad dielectric typically delivers >3 kVAC breakdown. For industrial or automotive applications running above 480 VAC, move to a thicker dielectric variant. Circuit design is the most important consideration for determining safety agency compliance — layout creepage and clearance distances matter as much as the raw material spec.

4. Base Metal Selection: Aluminum vs. Copper

The base layer is not just structural — it’s the primary heat spreader. The copper substrate offers 390 W/mK conductivity while aluminum offers 205 W/mK conductivity. Aluminum wins on cost, weight, and machinability, making it the right choice for the majority of applications including LED lighting, consumer audio, and standard power conversion. Copper is the choice when matching CTE to ceramic-packaged devices is critical, when the application requires double-sided assembly using the base as part of the circuit, or when maximum heat spreading is paramount.

You should match the base and circuit coefficients of thermal expansion (CTE). Failure to do this may cause excess plated-hole fatigue during thermal cycles. In the application, the CTE of the base material is a dominant contributor to thermal mechanical stress. This is why copper-base Thermal Clad is used in high-reliability designs where components have ceramic packages — the CTE mismatch between aluminum and a ceramic component body creates more stress than many high-cycle applications can tolerate.

5. Assembly Process and Solder Temperature Compatibility

Standard Thermal Clad dielectrics are compatible with SAC305 lead-free reflow at peak temperatures around 260°C. HT dielectrics are rated to 325°C/60 seconds, making them appropriate for higher-temperature solder pastes and gold wire bonding. If your assembly process involves potting compounds, check that the potting material’s cure temperature doesn’t approach the Tg of your chosen dielectric — potting at 150°C with an LTI dielectric (Tg ~130°C) is a common mistake that shows up as delamination failures in the field.

Base Metal Thickness and Circuit Flatness

Circuit flatness can be a concern when the base layer is aluminum. To achieve a flat circuit, maintain the proper ratio of circuit layer thickness to base. If the thickness of the copper circuit layer is kept at 10% of the base layer thickness or thinner, the aluminum base will mechanically dominate, keeping the circuit flat.

In practice, with a 1.57 mm (0.062″) aluminum base, your circuit copper should stay at or below roughly 157 µm — about 4.5 oz — to maintain flatness. Most designs using 1 oz or 2 oz copper are comfortably inside this envelope. Deviation from this ratio shows up as bow and twist that causes solder paste printing issues and component misalignment on automated lines.

Bergquist PCB Material Selection: A Practical Decision Framework

The table below is a simplified decision matrix to get engineers to the right dielectric family quickly.

Bergquist Thermal Clad vs. FR-4 and Alternatives

Engineers sometimes ask whether Thermal Clad is actually necessary or whether a thermally enhanced FR-4 (e.g., a high-Tg, thermally filled epoxy laminate) is sufficient. For designs under ~1–2 W/component with good heatsink access and relaxed temperature targets, thermally enhanced FR-4 is a legitimate option. But for power-dense SMD boards where the component body is the only thermal interface to the board, Thermal Clad’s metal base makes a dramatic difference.

Compared to competing IMS products such as Arlon PCB materials and other IMS laminates, Bergquist Thermal Clad benefits from a uniquely well-documented qualification history — new materials undergo a rigorous 12 to 18 month qualification program, and the lab facilities are UL certified with ISO 9001:2000 manufacturing certification. Extensive qualification testing consists of mechanical property validation, adhesion, temperature cycling, thermal and electrical stress — with electrical testing performed at selected intervals to 2000 hours where final evaluation is completed. That paper trail matters for products going through UL, CE, or automotive safety agency review.

Assembly and Manufacturing Considerations

Getting a Thermal Clad board assembled correctly requires a few process adjustments compared to FR-4.

Hipot Testing: Due to the capacitive nature of the circuit board construction, it is necessary to control the ramp-up of the voltage to avoid nuisance tripping of the failure detect circuits in the tester and to maintain effective control of the test. Step the voltage up slowly — a sudden ramp to the full test voltage will trip false failures on Thermal Clad boards due to displacement current. This is a common cause of confusion during first-article testing.

Drill and Route Tooling: Aluminum-base MCPCB requires carbide tooling. Standard HSS drill bits wear rapidly on the metal base and will produce rough hole walls and burring that affects via reliability.

Solder Stencil Printing: The standard SMT stencil approach applies without modification for most Thermal Clad designs. Dispensing of solder to specific locations is used for secondary operations or special attachment requirements, particularly for large power devices where controlled solder volume reduces voiding.

Conformal Coating: For outdoor or high-humidity environments, conformal coating can be applied over the assembled Thermal Clad board. Check the curing process temperature against the dielectric Tg before specifying a thermally cured coating.

Useful Resources for Bergquist PCB Material Selection

FAQs About Bergquist PCB Material Selection

1. How do I decide between the LTI and MP dielectric in Bergquist PCB material selection?

The core differentiator is thermal load. If your power dissipation per component is moderate, steady-state board temperature stays below 100°C, and you have some tolerance for a slightly elevated junction temperature, LTI at ~1.5 W/m-K is adequate and more cost-effective. If you’re running higher watt-density components, if your thermal model shows the LTI board running within 15°C of its Tg, or if reliability over a long thermal cycling life is critical, step up to MP at ~2.4 W/m-K. The price premium for MP over LTI is typically modest relative to the overall BOM cost and worth it for the extra thermal margin.

2. Can I use Bergquist Thermal Clad for multi-layer PCBs?

Yes, though it’s less common than single-layer Thermal Clad designs. Bergquist dielectrics can be used in multi-layer assemblies by bonding Thermal Clad dielectrics to a metal base using FR-4 or additional Thermal Clad circuit materials, depending on thermal requirements and cost objectives. In power conversion applications especially, replacing FR-4 prepreg with Thermal Clad dielectric in the inner layer stack is done to enhance thermal performance without moving to a full IMS board architecture.

3. What happens if I operate a Bergquist dielectric above its glass transition temperature?

The mechanical and electrical properties of the thermal clad will change when operating above the glass transition. You will notice that the CTE increases and the peel strength reduces. The storage modulus of the thermal clad also declines. In practice this means the dielectric bond to the copper circuit layer becomes weaker, the board becomes more susceptible to delamination under thermal cycling, and electrical properties degrade. Sustained operation above Tg will progressively damage the dielectric and shorten the product’s serviceable life. Always maintain a comfortable margin below Tg under worst-case temperature conditions.

4. Is Bergquist Thermal Clad compatible with standard pick-and-place and reflow assembly?

Yes. One of the practical advantages of Thermal Clad over ceramic or thick-film alternatives is its compatibility with automated SMT assembly. Standard stencil printing, SAC305 reflow profiles (peak ~260°C), and automated optical inspection all apply without special accommodation. The HT dielectric family extends compatibility further, rated for 325°C/60s solder floats, enabling gold wire bonding and higher-temperature attachment processes. The main process adjustment to watch is hipot testing procedure — use a controlled ramp rate rather than a step change to avoid false failures.

5. How does the dielectric thickness affect both thermal and voltage performance in Bergquist materials?

Dielectric thickness is a direct trade-off: thinner dielectric reduces thermal resistance (better heat transfer) but also reduces breakdown voltage and isolation margin. The HPL-03015’s 38 µm (1.5 mil) dielectric achieves exceptional thermal resistance of 0.02°C·in²/W precisely because it is so thin — but its application domain is high-power LED where voltage isolation requirements are moderate. For higher-voltage industrial or automotive applications, the thicker 6-mil (152 µm) or 10-mil (254 µm) dielectric options provide the breakdown voltage headroom needed to meet safety agency requirements. Always match dielectric thickness to both the thermal and voltage requirements of your specific application, not just one or the other.

Conclusion

Getting Bergquist PCB material selection right comes down to honestly characterizing your application: operating temperature, power density, voltage class, assembly process, and cost target. The Thermal Clad family covers a wide performance range — from the economical LTI for consumer applications through the high-performance HT and HPL for demanding LED and power electronics work — and each family member has a legitimate place in that range. The mistake most engineers make is picking a dielectric based on what was used in a previous revision without revisiting whether those assumptions still hold in the new design. Run your thermal model, check your Tg margin, confirm your voltage clearance, and then pick the lowest-tier dielectric that genuinely meets those requirements. That discipline is the core of sound Bergquist PCB material selection.

All specifications should be verified against current official Bergquist/Henkel datasheets before design lock-in. Material properties are subject to revision by the manufacturer.

Suggested Meta Description

Meta Description (158 characters):

Complete Bergquist PCB material selection guide: compare LTI, MP, HT, HPL dielectrics, base metal options, design rules & datasheets. Written for PCB engineers.

The post Bergquist PCB Material Selection Guide: How to Choose the Right Dielectric appeared first on RayPCB.

Finding a reliable Bergquist PCB manufacturer is harder than it looks. You’re not just buying a standard FR-4 board — you’re sourcing a thermally engineered substrate where the dielectric material itself is the performance variable, and where a bad laminate choice or an unqualified fabricator can quietly kill your LED luminaire or power module before it ever reaches the field.

This guide covers what’s actually changed in the Bergquist supply chain, how to evaluate fabricators who claim to work with Thermal Clad, what certifications to ask for before you place an order, and what red flags separate genuinely experienced IMS shops from those that just know how to use the right keywords on their website.

What “Bergquist PCB” Actually Means in 2025

Before you start shortlisting suppliers, it helps to understand the ownership history — because it directly affects which manufacturer is the authoritative source for genuine Thermal Clad material.

The Bergquist Company originally developed the Thermal Clad IMS technology. In 2014, Bergquist and its Thermal Clad division were acquired by Henkel, bringing global resources and reach. Then in 2021, a new chapter began — Polytronics Technology Corp. acquired the Thermal Clad division from Henkel and the TCLAD company was formed. Today, TCLAD operates from its 100,000 sq. ft. Innovation Center in Prescott, Wisconsin, supported by a team of over 200 employees.

The long-awaited purchase of the Bergquist Thermal Clad product line from Henkel is now complete. TCLAD Inc., a Delaware corporation, finished the acquisition including all assets, business, facilities, and technology of the Thermal Clad product line. All in-house personnel including sales, technical, and direct employees remain a part of the new TCLAD Inc. team, with manufacturing headquarters remaining in Prescott, Wisconsin.

What this means practically: “Bergquist PCB” is now a colloquial term. The actual material brand is TCLAD, and the laminate manufacturer is TCLAD Inc. When a Chinese or overseas PCB fab says they build “Bergquist PCBs,” they mean they purchase TCLAD-brand laminate sheets and fabricate circuits from them — they are not the material manufacturer themselves. This distinction matters enormously when you’re qualifying your supply chain.

The Two Tiers of Supply: Laminate vs. Fabricated Circuit

One of the most common points of confusion when sourcing Thermal Clad boards is conflating the laminate supplier with the PCB fabricator. These are different entities serving different functions.

When you’re evaluating a “Bergquist PCB manufacturer,” you need to establish which tier they occupy. A fab claiming to be a Bergquist manufacturer is almost certainly a fabricator purchasing genuine TCLAD laminate and etching circuits from it — which is completely legitimate, provided they can prove material traceability back to TCLAD Inc.

Why Material Traceability Is Non-Negotiable

Here is where engineers make expensive mistakes. Generic aluminum-core MCPCBs are widely available, and on paper many of them look similar to Thermal Clad. Some low-cost suppliers substitute generic aluminum-base copper clad laminate using standard prepreg as the dielectric, which doesn’t provide the high thermal conductivity and resulting thermal performance required to assure the lowest possible operating temperatures for high-intensity LEDs.

The thermal performance difference is not subtle. TCLAD HPL-03015 achieves a thermal conductivity of 7.5 W/m·K through its proprietary polymer-ceramic dielectric. Generic aluminum PCB materials typically achieve 1.0–2.0 W/m·K at best. If your thermal model is built around genuine TCLAD material and your fab swaps in a generic equivalent without disclosing it, your LED array will run 15–25°C hotter than predicted — and your reliability predictions become meaningless.

Always request a material certificate (mill cert) with each production lot. This is a standard practice with any structural or thermally critical material and there’s no legitimate reason a reputable fab should refuse it.

Key Certifications to Verify Before Placing an Order

Certifications tell you whether a PCB fabricator has had their processes audited by a third party — and more importantly, to what standard. For Bergquist Thermal Clad boards, these are the most relevant:

ISO 9001:2015

This is the baseline quality management system certification and should be considered the minimum for any fab you work with. ISO certification ensures that the holder follows a quality management system and standard documentation, which helps to track and control process variations and maintain consistent quality. Without ISO 9001, you have no assurance that their processes are documented and controlled enough to be repeatable across production lots.

UL Certification (UL 796 / UL 94)

For PCBs, the primary standard is UL 796, the specific PCB standard, and UL 94 for flammability testing of all plastics. UL request manufacturers to strictly test their products by following correct procedures to minimize quality issues and safety problems. The products that are UL certified undergo more rigorous and stricter tests.

For LED luminaire designs that need UL Listed or UL Recognized Component marks on the final product, your PCB fabricator must have UL-recognized facility status. To prove to your end customer that PCBs have been manufactured in UL-approved facilities, you may ask your PCB supplier either to provide a certificate or print the UL logo/UL number on PCBs. UL is extremely strict these days, so it is very unlikely that a non-UL-approved PCB manufacturer will accept such a request.

IPC Class 2 vs. Class 3

IPC certifications define workmanship and inspection standards for PCB assemblies. Each class reflects a different performance objective, from basic function to continuous service in extreme conditions. For most commercial LED and power electronics applications, IPC Class 2 is the standard expectation. If you’re designing for automotive (under IATF 16949 requirements), defense, or medical applications, require IPC Class 3.

IATF 16949 (Automotive)

If your Thermal Clad board goes into an automotive LED headlamp system or EV power module, your fab needs IATF 16949 certification — not just ISO 9001. IATF 16949 adds automotive-specific requirements for process control, defect prevention, and supply chain management that standard ISO doesn’t cover.

RoHS Compliance

Verify that the fab’s surface finishes and solder materials are RoHS-compliant. For Thermal Clad boards, ENIG (Electroless Nickel Immersion Gold) is the preferred surface finish for LED applications and is inherently lead-free.

Certification Quick Reference Table

How to Evaluate an IMS PCB Fabricator: A Practical Checklist

Beyond certifications, here’s what to actually dig into when qualifying a Bergquist PCB manufacturer:

Confirm Genuine TCLAD Laminate Sourcing

Ask directly: “Where do you source your Thermal Clad dielectric?” and “Can you provide a TCLAD material certificate with our order?” A qualified fab will answer this without hesitation and will have an established relationship with TCLAD Inc. or an authorized distributor. Evasive answers here are a serious red flag.

Assess IMS-Specific Process Experience

IMS fabrication is different from standard FR-4 manufacturing. Routing aluminum requires carbide or diamond-tipped tooling. Drilling requires different parameters to avoid delamination at the dielectric-aluminum interface. Solder mask application on single-layer IMS requires attention to coverage at board edges. Ask how many IMS board designs the fab processes per month and request reference customers in your industry vertical.

Review DFM Feedback Quality

Send a representative Gerber package and request a DFM review. A competent IMS shop will flag issues specific to metal core boards: insufficient copper-to-edge clearance, incorrect drill parameters for aluminum, soldermask spec issues for high-reflectance white mask, and pad design concerns for thermal performance. If their DFM review reads like a generic FR-4 checklist, that’s telling.

Evaluate Lead Time Realism for Specialty Material

TCLAD material is not FR-4 — it has longer procurement lead times, especially for less-common dielectric grades. TCLAD operates from its 100,000 sq. ft. Innovation Center in Prescott, Wisconsin, with global footprint including operating divisions in Frankfurt, Germany and Hsinchu City, Taiwan. A fab quoting you 5-day lead time on HPL-03015 boards without having raw material in stock should prompt follow-up questions about how they’re achieving that timeline.

Prototyping to Production Continuity

Confirm that the fab uses the same material grade, the same process parameters, and the same equipment for prototype and production runs. Changing fabs or processes between prototype and production on an IMS board is a common source of thermal performance variability that’s difficult to catch without exhaustive testing.

Geographic Considerations: Domestic vs. Overseas Sourcing

The choice between domestic and overseas Bergquist PCB manufacturer options involves trade-offs that go beyond unit cost.

For prototypes and initial design verification, domestic sourcing from an authorized TCLAD circuit fabricator gives you the clearest material traceability and the easiest access to technical support. For volume production, qualified overseas fabs using verified TCLAD laminate can offer significant cost reduction — but the qualification process upfront is more intensive.

For alternative IMS substrate materials worth evaluating alongside TCLAD, engineers sometimes compare Arlon PCB laminates, which offer their own line of thermally conductive substrate options for demanding applications.

Red Flags to Watch for When Sourcing

These are the supplier behaviors that should immediately trigger further scrutiny:

Claims to manufacture the dielectric itself. Unless you’re talking to TCLAD Inc. directly, no PCB fabricator manufactures genuine Thermal Clad dielectric. Any supplier claiming to manufacture their own equivalent should be asked to provide independent material characterization data — not just a spec sheet they wrote themselves.

No material traceability documentation. If a supplier can’t or won’t provide lot-traceable material certificates linking your boards to a TCLAD laminate lot, you have no way to verify what dielectric is actually in your boards.

Thermal resistance specs that seem too good. Generic aluminum PCBs are sometimes marketed with inflated thermal conductivity claims. If a supplier is quoting thermal conductivity significantly above 2.2 W/m·K for HT-series equivalent material, ask for the independent test data. HPL-03015’s 7.5 W/m·K is genuinely exceptional and is a function of TCLAD’s proprietary dielectric chemistry — not something a generic fab can replicate.

No IPC-6012 or IPC-A-600 inspection capability. These standards define how IMS boards are inspected. A fab without these inspection protocols in place is not equipped to catch the defect modes specific to metal core substrate fabrication.

Useful Resources for Bergquist PCB Sourcing and Qualification

Frequently Asked Questions

Q1: Can any PCB fabricator process Bergquist Thermal Clad material, or do I need an “authorized” manufacturer?

TCLAD Inc. sells laminate through distributors, and technically any fab that purchases it can build circuits from it. However, IMS fabrication requires tooling, process parameters, and inspection capabilities specific to aluminum-base boards. In practice, you want a fabricator who regularly processes metal core boards at volume — not one who occasionally does a run when a customer requests it. Ask for references and look for a fab that lists IMS as a core capability, not a specialty service. TCLAD Inc. can also provide guidance on their recommended circuit fabricators if you contact their technical team directly.

Q2: How do I know if my overseas supplier is using genuine TCLAD material versus a generic substitute?

The most reliable method is requiring a material certificate (mill cert) for each production lot that includes the TCLAD part number, lot number, and date of manufacture. You can cross-reference this with TCLAD Inc. if needed. As a secondary check, request thermal conductivity test data for a sample board from your production lot — a properly built HPL-03015 board should measure close to 7.5 W/m·K. A significant deviation from the datasheet value is a strong indicator of material substitution.

Q3: What’s the minimum order quantity for TCLAD laminate boards, and does it affect supplier selection?

For prototype quantities (typically 5–25 boards), most IMS-capable fabs can accommodate small runs, though setup costs are amortized over fewer boards so unit pricing is higher. For production volumes above 500 boards per run, you’ll have more supplier options and better pricing leverage. Some overseas fabs have minimum order quantities tied to full panel sizes — understand your fab’s panelization strategy since it affects material yield and ultimately unit cost.

Q4: Is IATF 16949 certification required for all automotive LED PCB applications?

Not universally — it depends on your customer’s requirements and your position in the supply chain. If you’re a Tier 1 or Tier 2 supplier shipping directly to an OEM automotive program, IATF 16949 is typically mandatory. If you’re supplying an aftermarket LED retrofit or an automotive accessory that doesn’t go through the Tier supply chain, ISO 9001 may be sufficient. Check your customer’s supplier quality requirements (SQR) documentation before assuming either way.

Q5: My design uses both standard FR-4 sections and a Thermal Clad area in the same assembly. Can one fab handle both?

For most designs, the Thermal Clad IMS board and the FR-4 control board are separate PCBs that are mechanically attached or connected via a flex or wire harness. True hybrid PCBs combining IMS and FR-4 regions in a single laminate are unusual and require specialized fabrication expertise — most standard IMS fabs don’t offer this. If your design genuinely requires a hybrid approach, verify this capability explicitly with your fabricator before committing to a design, and expect longer lead times and higher costs.

Summary

The search for a reliable Bergquist PCB manufacturer really comes down to three things: confirming you’re getting genuine TCLAD material with traceable lot documentation, verifying the fab has the certifications and process capability to handle aluminum-base IMS boards correctly, and doing enough diligence upfront to avoid the expensive discovery that your thermal model doesn’t match your production boards.

TCLAD continues to innovate from its vertically integrated U.S. manufacturing center, delivering thermal management solutions for high-power density applications worldwide — but the quality of the circuit board you receive depends equally on the fabricator who processes that laminate. Invest the time in supplier qualification before your first production run, and you’ll avoid the kind of field failures that come from cutting corners on a material that’s doing serious engineering work in your design.

Meta Description Suggestion:

Looking for a reliable Bergquist PCB manufacturer? This engineer’s guide covers TCLAD supply chain changes, material certification, supplier qualification checklists, IMS fabricator red flags, and useful sourcing resources. (157 characters)

The post Bergquist Thermal Clad PCB Manufacturer: How to Find a Reliable Supplier appeared first on RayPCB.

When thermal management stops being a footnote and becomes the whole problem, most experienced power electronics engineers end up in the same place: metal core PCBs. And within that category, the Bergquist HT-04503 consistently shows up on short lists for high-watt-density, high-temperature applications. Part of the Thermal Clad family from Bergquist (now a Henkel brand), the HT-04503 is not a general-purpose MCPCB material — it’s an engineered dielectric optimized for applications where standard aluminum PCB substrates run out of headroom.

This guide compiles the full specification data, explains what the numbers actually mean for your design, positions the HT-04503 against other Thermal Clad grades, and gives you the practical design guidance you need to use it correctly.

What Is the Bergquist HT-04503?

The HT-04503 is a Thermal Clad insulated metal substrate (IMS) from Bergquist, characterized by a 3 mil (76 µm) dielectric layer designed for high-temperature service. The product code tells you the key parameters directly: “HT” stands for High Temperature, “045” refers to the dielectric thickness (0.003″ = 3 mil, with “045” being an internal designation tied to thermal resistance), and “03” indicates the 3 mil dielectric thickness in the Bergquist naming convention.

The dielectric itself is a proprietary polymer/ceramic blend — not standard epoxy. The polymer component provides electrical isolation and resistance to thermal aging. The ceramic filler is what drives thermal conductivity while maintaining dielectric strength at thicknesses where standard epoxy resins would begin to show pinholes and breakdown. This combination allows the HT-04503 dielectric to hold a breakdown voltage of 8.5 kVAC at just 76 µm thickness — a figure that should get attention from anyone designing for mains-isolated power electronics.

The “High Temperature” designation is meaningful, not marketing. The HT dielectric maintains its properties at continuous operating temperatures up to 140°C (U.L. 796 rated), with a glass transition temperature of 150°C. That puts it in a different tier from standard MCPCB materials, which typically begin to soften and lose bond strength well below that range.

Bergquist HT-04503 Full Datasheet Specifications

The table below presents the complete published technical data from the official Bergquist HT-04503 datasheet. Every value listed corresponds to a named test method — a point worth emphasizing when comparing competing MCPCB substrates, where thermal conductivity figures are sometimes cited without methodology.

Table 1: Bergquist HT-04503 Complete Technical Specifications

Understanding the Two Thermal Conductivity Values

A common point of confusion is why the datasheet lists two thermal conductivity values: 4.1 W/m-K for “Product Thermal Conductivity” and 2.2 W/m-K for “Dielectric Thermal Conductivity.” These are not contradictory — they measure different things.

The 4.1 W/m-K figure is a system-level measurement (Bergquist’s proprietary MET test method using a TO-220 setup) that accounts for the full substrate stack including the aluminum base and copper circuit layer. The 2.2 W/m-K value is the intrinsic thermal conductivity of the dielectric layer alone, measured via ASTM D5470. When you’re modeling thermal resistance in a design tool, the 2.2 W/m-K dielectric-only value is what you’ll use alongside the dielectric thickness to calculate junction-to-baseplate thermal resistance. The 4.1 W/m-K figure is useful for comparative benchmarking against competing products but cannot be directly substituted into a layer-by-layer thermal model.

The thermal resistance specification of 0.05°C·in²/W at 3 mil dielectric thickness is a direct output of that ASTM D5470 measurement. To put it in context: standard aluminum MCPCB materials at equivalent dielectric thicknesses typically land between 0.10 and 0.20°C·in²/W. The HT-04503 essentially halves the thermal resistance of a typical entry-level MCPCB dielectric.

Bergquist HT-04503 vs. Other Thermal Clad Grades

The HT-04503 doesn’t exist in isolation — it’s one product in the Thermal Clad lineup. Engineers selecting MCPCB materials should understand where the HT series sits relative to the Multi-Purpose (MP) and High Power Lighting (HPL) grades.

Table 2: Bergquist Thermal Clad Grade Comparison

The comparison reveals how each grade trades off thermal resistance against electrical isolation. The HT-04503 occupies the sweet spot for most high-power industrial applications: thinner dielectric than the HT-07006 (lower thermal resistance, higher temperature capability), more isolation voltage than the HPL-03015 (which is optimized for LED boards where mains isolation is not the priority), and significantly better high-temperature performance than the MP-06503 general-purpose grade.

If your design is a mains-connected power converter running at sustained high ambient temperatures, the HT-04503 is the appropriate choice. If you’re building a high-bay LED fixture operating at lower ambient temperatures with modest isolation requirements, the HPL-03015 may offer better thermal performance at the cost of isolation voltage margin.

Decoding the Part Number and Available Configurations

The Bergquist Thermal Clad HT-04503 is available on both aluminum and copper metal substrates — a point sometimes overlooked in procurement. Aluminum is the standard choice for cost and weight, but copper-base variants are available for applications where higher thermal spreading (leveraging copper’s roughly 4× higher thermal conductivity vs. aluminum) justifies the cost and weight penalty.

Standard MCPCB Stack-Up Using HT-04503

A typical single-layer HT-04503 MCPCB consists of three layers from top to bottom:

Circuit Layer (Copper Foil): The component mounting and interconnect layer. Standard offerings are 1 oz (35 µm) copper, with 2 oz (70 µm) available for higher current carrying capacity. The copper foil is certified to an area weight requirement per IPC-4562 rather than measured directly for thickness — a nuance worth noting when specifying to a fabricator.

Dielectric Layer (HT-04503): The 3 mil (76 µm) polymer-ceramic blend. This is the thermal and electrical performance layer. Its CTE of 25 µm/m·°C below Tg provides reasonable match to both the aluminum base (~23 µm/m·°C) and copper circuit layer (~17 µm/m·°C), reducing interfacial stress during thermal cycling.

Metal Base (Aluminum or Copper): Typically 1.0 mm, 1.5 mm, or 2.0 mm thick aluminum (6061 or 5052 alloy). Acts as the primary heat spreader and mechanical substrate. The base attaches to a heatsink via thermal interface material or direct bolted contact.

Table 3: Standard HT-04503 Board Configuration Options

PCB Design Guide: Getting the Best from Bergquist HT-04503

Selecting the right material is step one. Getting the design right to exploit its properties is the part that separates boards that perform from boards that just test okay.

Thermal Via and Pad Design Considerations

One critical difference between designing for MCPCB and standard FR-4: through-holes in MCPCB are electrically isolated blind stubs, not continuous barrels connecting to the metal base. In standard Thermal Clad construction, drilled holes are lined with the same dielectric system and do not penetrate the metal base. This means conventional thermal vias to the baseplate aren’t available — the dielectric provides the only thermal path from the circuit layer to the aluminum base.

For surface-mount power components, this makes pad geometry critical. Thermal pads under components should be maximized within DFM constraints to spread the heat flux over the largest possible dielectric area. Since thermal resistance scales inversely with contact area (R_th = R_material / A), doubling the effective pad area under a MOSFET or LED package halves the component’s contribution to junction-to-baseplate thermal resistance.

Direct screw-mount thermal pads — with the dielectric separating the component’s thermal slug from the aluminum baseplate — are a particularly effective topology. The HT-04503’s 8.5 kVAC breakdown voltage provides ample margin for most industrial mains-connected designs using this approach.

Solder Mask and Surface Finish Selection

The HT-04503 is rated for maximum soldering temperatures of 325°C for 60 seconds (U.L. 796). Lead-free SAC305 reflow peaks at approximately 250–260°C, leaving substantial margin. Eutectic AuSn (80/20) compatibility at higher process temperatures is also specified, which matters for die-attach applications in solid-state relay and power module constructions.

ENIG (Electroless Nickel Immersion Gold) surface finish is generally preferred over HASL on MCPCB for fine-pitch surface mount components because HASL can produce uneven deposit thickness that complicates coplanarity on small packages. For LED applications, a white solder mask significantly improves optical efficiency by reflecting secondary light emission from the PCB surface rather than absorbing it.

Trace Width and Current Carrying Capacity on MCPCB

The copper circuit layer on an HT-04503 board carries current just like any other PCB copper, but with an important advantage: because the dielectric efficiently transfers heat to the aluminum baseplate, traces on MCPCB can sustain higher continuous current than the same geometry on FR-4 at the same temperature rise. IPC-2152 current-carrying capacity tables, which are derived from FR-4 data, are conservative for MCPCB — but unless you have empirical data for your specific thermal configuration, using IPC-2152 as a starting point and applying a derating factor remains the safe engineering approach.

For high-current applications (motor drive bus bars, power converter output stages), 2 oz or 3 oz copper is available and worthwhile. The thermal dissipation from I²R losses in the copper itself becomes a secondary heat source that the dielectric must also conduct — heavier copper reduces this contribution.

Mechanical Mounting and Assembly Considerations

The aluminum base of an HT-04503 MCPCB can be mounted directly to a heatsink using thermal interface material (TIM). Bergquist also offers compatible Bond-Ply and Hi-Flow TIM products for this interface, which is convenient for supply chain management if you’re already specifying Bergquist for the MCPCB substrate.

For designs with multiple MCPCBs in a chassis, consider the CTE mismatch between the 3003/5052 aluminum base (~23 µm/m·°C) and steel or cast aluminum chassis hardware when designing fastener patterns for boards that experience wide temperature swings. The HT-04503 dielectric’s CTE of 25 µm/m·°C below Tg closely tracks the aluminum base, which keeps internal stress at the dielectric-metal interface controlled through the normal operating range.

Application Profiles: Where Bergquist HT-04503 Excels

Table 4: HT-04503 Application Suitability Guide

Comparing HT-04503 to Alternative High-Performance MCPCB Materials

For completeness, engineers evaluating the HT-04503 should understand where it sits against other premium MCPCB substrate families. The Arlon PCB material portfolio offers alternative high-temperature IMS options for applications where different thermal/electrical trade-offs are needed. Ceramic substrates (AlN, Al₂O₃) offer better CTE matching to silicon but at significantly higher cost and with brittleness constraints. The HT-04503’s polymer-ceramic dielectric falls between standard MCPCB and ceramic in performance — closer to ceramic in thermal capability but with the manufacturing flexibility and cost profile of a conventional PCB process.

Table 5: HT-04503 vs. Alternative Thermal Management Substrates

Fabrication Notes: Working With HT-04503 MCPCB Material

A few process details worth knowing before sending files to your fabricator:

Dielectric Testing. Because micro-fractures or micro-voids in the dielectric can manifest as electrical shorts under voltage, Bergquist recommends testing finished boards with a controlled voltage ramp rate. The capacitive nature of the MCPCB construction (capacitance of 540 pF/in² is substantial) can cause nuisance trips if testers apply voltage too rapidly. Specify a controlled ramp-up per Bergquist fabrication guidelines.

Drilling. MCPCB drilling requires carbide tooling and controlled parameters to prevent dielectric cracking or delamination at hole walls. Through-hole components work, but pad connections to the base metal are not electrically available — all through-holes are dielectrically isolated from the aluminum base.

Solder Mask Application. Standard liquid photoimageable (LPI) solder masks are compatible. For white solder mask on LED boards, verify that your fabricator’s white LPI formulation has been qualified with MCPCB substrates — adhesion characteristics differ from FR-4.

Storage. Bergquist specifies optimal storage at 5–25°C with a 12-month shelf life in unopened packaging. Moisture absorption (0.24% water vapor retention per ASTM E595) is relatively controlled, but pre-baking before assembly is recommended if material has been stored in humid conditions.

Useful Resources for Engineers Working With HT-04503

Bookmark these references for material qualification, design validation, and procurement:

Official Datasheets and Documentation

• Bergquist HT-04503 Official Datasheet (PDF via mclpcb.com) — Full specification table with test methods
• Bergquist Thermal Clad Selection Guide (PDF via Digikey) — Comprehensive guide comparing all Thermal Clad dielectrics, stack-up options, and design guidelines
• Henkel Bergquist Product Portfolio — Current product listing after Bergquist acquisition by Henkel

Standards Referenced in HT-04503 Datasheet

• ASTM D5470 — Standard Test Method for Thermal Transmission Properties of Thermally Conductive Electrical Insulation Materials
• ASTM D149 — Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials
• IPC-2152 — Standard for Determining Current Carrying Capacity in Printed Board Design

Distributor and Procurement

• Digikey — Bergquist Thermal Clad Products — Stock and pricing data for HT-04503 and related products
• Mouser — Bergquist IMS Materials — Alternative distributor with lead time information

Frequently Asked Questions About Bergquist HT-04503

What makes the HT-04503 a “high temperature” MCPCB material?

The designation refers to the dielectric polymer system, which is formulated to resist thermal degradation at sustained elevated temperatures. The glass transition temperature of 150°C and U.L.-certified maximum operating temperature of 140°C distinguish it from standard MCPCB dielectrics (typically Tg ~130°C, operating limit ~105–125°C). In practice this means the HT-04503 maintains its mechanical integrity, bond strength, and electrical isolation properties through repeated excursions toward 140°C, where a standard MCPCB dielectric would begin softening and losing peel strength.

What is the difference between the HT-04503 and HT-07006?

Both are High Temperature series Thermal Clad materials, but the HT-07006 uses a 6 mil (152 µm) dielectric instead of the 3 mil (76 µm) in the HT-04503. The thicker dielectric in the HT-07006 raises breakdown voltage to 11 kVAC (vs. 8.5 kVAC for HT-04503) at the cost of higher thermal resistance. Choose the HT-04503 when thermal performance is the priority and 8.5 kVAC isolation is sufficient. Choose the HT-07006 when your isolation requirements demand greater voltage margin — for instance, in 480 VAC industrial equipment where creepage and clearance requirements plus safety margins push isolation needs above what the 3 mil product provides.

Can the Bergquist HT-04503 be used for double-sided or multilayer MCPCB?

Single-sided construction (one copper circuit layer over the dielectric and metal base) is the standard and most common configuration. Double-sided MCPCB is technically possible but requires specialized construction — typically two single-sided substrates bonded back-to-back with a thermally conductive adhesive, or use of Bergquist’s Bond-Ply adhesive films to build up multilayer assemblies with thermal vias in the dielectric. True through-hole multilayer MCPCB with the base metal as a middle layer is a specialty construction that should be explicitly discussed with your fabricator before committing to the design.

Is the Bergquist HT-04503 suitable for automotive applications?

The material properties — 150°C Tg, 140°C UL operating temperature, lead-free solder compatibility, and CTE of 25 µm/m·°C — are consistent with automotive under-hood requirements. However, “suitable” in the automotive sense requires AEC-Q component-style qualification, which is application-specific. The material passes the thermal, electrical, and mechanical benchmarks that automotive designs demand. Whether it meets your specific OEM’s supplier qualification requirements is a separate process that requires engaging Henkel/Bergquist directly through their automotive channel.

How does the HT-04503 thermal resistance compare to using thermal vias in FR-4?

An optimized via-in-pad array in FR-4, filled with thermally conductive epoxy, can achieve effective thermal conductivity of roughly 1–3 W/m-K through the via cluster — considerably less than the HT-04503 dielectric’s 2.2 W/m-K over its full surface. More importantly, the thermal path in FR-4 with vias is discontinuous and sensitive to via fill quality, while the HT-04503 dielectric provides a continuous, uniform thermal path across the entire component footprint. For component junction temperatures above ~100°C under sustained load, or for designs where thermal resistance budget is tight, the MCPCB approach using HT-04503 consistently outperforms FR-4 with thermal vias.

The HT-04503 is one of those materials that rewards the engineer who takes the time to understand its specifications properly. The thermal resistance number is exceptional, the isolation voltage is better than it has any right to be at 3 mil thickness, and the temperature capability puts it in territory that FR-4 and generic MCPCB materials simply can’t reach. Design it right, specify your fabricator’s process correctly, and this material will outlast the components mounted on it.

The post Bergquist HT-04503 MCPCB: Datasheet, Specifications & Design Guide appeared first on RayPCB.

If you’ve been designing insulated metal substrate (IMS) PCBs for any length of time, you’ve probably run into a familiar constraint: standard single-layer Thermal Clad works brilliantly for straightforward power LED and motor control boards, but the moment your design demands multiple signal layers, combined power and control routing, or true multilayer stack-up integration, the options narrow quickly. That’s where the Bergquist ML-11006 earns its place.

The ML-11006 is Bergquist’s thermally conductive, multi-layer capable dielectric — specifically the CML (Ceramic Multi-Layer) family — offered in prepreg form and engineered for engineers who need to combine the superior thermal management of IMS technology with the routing complexity of conventional multi-layer PCB construction. This article covers the ML-11006’s specifications, how the naming convention decodes, where it fits in the broader Bergquist product ecosystem, and how to decide whether it’s the right material for your next high-power, thermally demanding design.

Understanding the Bergquist Thermal Clad Dielectric Family

Before diving into the ML-11006 specifically, it’s worth establishing how it sits within Bergquist’s broader Thermal Clad product architecture.

Thermal Clad circuit board materials are available from The Bergquist Company in four different thermal conductivities: High Power Lighting (HPL), High Temperature (HT), Low Modulus (LM) and Multi-Purpose (MP). The CML — Ceramic Multi-Layer — family is the fifth key member of the dielectric lineup, specifically distinguished by its availability in prepreg form for multi-layer constructions.

CML is available in prepreg form, which is what fundamentally separates it from the other Thermal Clad grades. Where HT, MP, HPL, and LM are single-substrate laminates applied to a metal base, CML/ML-series dielectrics can be laminated between circuit layers in the same way conventional FR4 prepregs are used — making true multi-layer IMS constructions possible.

Thermal Clad substrates minimize thermal impedance and conduct heat more effectively and efficiently than standard printed wiring boards (PWBs). These substrates are more mechanically robust than thick film ceramics and direct bond copper constructions that are often used in these applications. Thermal Clad is a cost-effective solution which can eliminate components, allow for simplified designs, smaller devices and an overall less complicated production process.

Decoding the Bergquist ML-11006 Part Number

What the Naming Convention Tells You

Bergquist’s Thermal Clad product codes follow a structured naming format that encodes the dielectric family, thermal characteristics, and dielectric thickness directly in the part number. For ML-series products:

• ML = Multi-Layer dielectric family (CML ceramic multi-layer, prepreg form)
• 110 = Thermal conductivity designator (nominally ~1.1 W/m·K)
• 06 = Dielectric thickness in mils (6 mil / 152 µm)

Cross-referencing with the broader CML family within the Bergquist product range:

The ML-11006 sits in the middle of the family: thicker than the 3-mil variants (giving more voltage isolation margin), thinner than the 9-mil version (giving lower thermal impedance), and at the higher thermal conductivity tier within the 6-mil options.

Bergquist ML-11006 Key Technical Specifications

The ML-11006’s specification profile reflects its dual role as both a thermal management material and a multi-layer dielectric bonding film. Based on published Bergquist/TCLAD CML series data:

Thermal Properties

Electrical Properties

Mechanical and Compliance Properties

Important: Always verify against the current Henkel/TCLAD technical data sheet before finalizing your design. Properties may vary with copper foil weight and lamination parameters.

What Makes the ML-11006 Distinctly a Multi-Layer Material

The Prepreg Form Factor Is the Key Differentiator

CML is the one exception because of its prepreg form — a glass carrier is needed for handling purposes. This single characteristic is what separates the ML family from every other Bergquist Thermal Clad grade. The glass carrier enables the CML dielectric to be handled, cut, and stacked exactly like conventional FR4 prepreg in a standard multilayer press cycle, without the handling challenges that a loose polymer/ceramic film would present in a production lamination environment.

Thermal Clad dielectric film is easy to laminate, simplifying the fabrication of advanced multi-layer circuit boards. By vertically stacking copper foils with glass-fiber-reinforced dielectric layers, we create complex circuit structures that deliver superior thermal conductivity, electrical isolation, and mechanical strength.

This architecture opens up a design space that single-layer IMS simply cannot address: high-power boards that also require dedicated control circuitry, isolated power rails on separate layers, or complex signal routing that a single-sided board cannot accommodate.

Thermal Conductivity in Context: Why 1.1 W/m·K Matters

An IMS PCB can be designed with a very low thermal resistance. If, for example, you compare a 1.60 mm FR4 PCB to an IMS PCB with a 0.15 mm thermal prepreg, you may well find the thermal resistance is more than 100 times that of the FR4 PCB.

Standard FR4 has a thermal conductivity of approximately 0.24 W/m·K. The ML-11006’s ~1.1 W/m·K represents roughly a 4.5× improvement in the dielectric layer itself — and because IMS construction uses a thin dielectric (6 mil vs. the 62-mil thickness of a typical FR4 board), the actual thermal impedance improvement at the system level is dramatically larger than the conductivity ratio alone suggests.

When selecting a material for an application, thermal impedance has to be taken into consideration. The thermal resistance (Rth) defines the interior thermal resistance of a material against a possible heat flow. The lower this value, the better the heat can be dissipated through the material.

For the ML-11006, the 6-mil dielectric thickness combined with 1.1 W/m·K conductivity gives a thermal impedance that is workable for moderate-power applications where the routing complexity of a multi-layer construction is more critical than achieving the absolute minimum thermal resistance.

Bergquist ML-11006 vs. Other Thermal Clad Dielectrics: Choosing the Right Grade

This comparison is where most engineers need to spend their time before finalizing a material specification.

Full Bergquist Thermal Clad Family Comparison

The trade-off is explicit: the ML-11006 offers lower thermal conductivity than HPL, HT, or LTI grades in exchange for multi-layer lamination capability. This is a fundamental materials engineering constraint — the glass carrier required for prepreg handling introduces a glass content that slightly reduces thermal conductivity compared to the glass-free Bergquist dielectrics used in single-layer configurations.

Glass carriers degrade thermal performance which is why our dielectrics are glass-free. CML is the one exception because of its prepreg form — a glass carrier is needed for handling purposes.

Engineers who need both maximum thermal performance and multi-layer routing must evaluate whether a hybrid approach — using a high-conductivity single-layer dielectric on the thermally critical outer layer and ML-series prepreg for inner-layer bonding — can deliver the best of both.

ML-11006 vs. ML-11009: When to Go Thicker

Choose ML-11009 when your inter-layer isolation voltage requirements demand more headroom — for example, in multilayer boards where high-voltage bus layers and low-voltage control layers coexist in the same stack-up at voltages approaching or exceeding 480V AC. Choose ML-11006 when thermal impedance is the tighter constraint and your voltage levels are moderate.

Primary Application Areas for the Bergquist ML-11006

Multi-Layer Power + Control Boards

This is the canonical ML-series use case. Many modern power conversion designs require both high-current power switching circuitry and dedicated microcontroller or gate driver circuitry on the same board — functions that benefit from the thermal management of IMS construction but require at least two signal layers to route effectively.

Two-layer constructions can provide shielding protection and additional electrical routing capability. The ML-11006 enables this two-layer or multi-layer construction while maintaining the thermal management benefits of Thermal Clad technology throughout the stack-up.

Advanced LED Driver and Lighting Systems

By maintaining standard FR4 layouts, this solution streamlines the transition to improved thermal performance with IMS. The integration of Thermal Clad dielectric and base metal enhances heat dissipation, increases mechanical strength, boosts component reliability, and delivers effective EMI shielding.

High-specification architectural lighting, horticultural LED systems, and stadium lighting fixtures increasingly use multi-layer driver boards where LED power circuitry, PWM control circuits, and communication interfaces all share the same physical board. The ML-11006 allows this integration without abandoning the thermal advantages of IMS.

Automotive Power Electronics

Automotive-grade power modules — DC-DC converters, OBC (onboard charger) modules, and EV battery management units — demand multi-layer routing for signal integrity, EMC compliance, and functional safety circuit separation, while simultaneously managing significant thermal loads from switching devices. The ML-11006’s multi-layer capability makes it a practical substrate option for these hybrid-architecture boards.

Industrial Motor Controls and Inverters

Compact high-reliability motor drives built on Thermal Clad have set the benchmark for watt-density. For motor control designs where a dedicated power layer handles high-current IGBT or MOSFET circuits and separate signal layers manage encoder feedback, CAN bus communication, or gate drive logic, the ML-11006 provides the lamination chemistry to build that stack-up with integrated thermal management.

Satellite Systems and High-Reliability Electronics

Multi-layer thermal clad PCBs using CML-type dielectrics are found in satellite systems, atomic accelerators, heart monitors, and file servers — applications where the combination of dense circuit routing and reliable thermal management in a compact form factor justifies the material’s higher engineering effort and cost relative to conventional FR4.

Fabrication and Design Considerations for ML-11006 Multi-Layer IMS PCBs

Stack-Up Design with ML-11006 Prepreg

The ML-11006 is used as the bonding prepreg between circuit layers in a multi-layer IMS stack-up. A typical two-signal-layer IMS construction using ML-11006 would be:

Layer 1 (Top): Circuit copper (1–3 oz) Bond Layer: ML-11006 prepreg (6 mil) Layer 2 (Bottom circuit): Circuit copper (1–3 oz) IMS Dielectric: ML-11006 or single-layer Thermal Clad Base Metal: Aluminum 5052/6061 or Copper C1100

When paired with a copper base plate, blind vias can be implemented to create conductive pathways between circuit layers and the base — boosting thermal conduction and electrical performance.

Base Metal Selection

Copper and aluminum Thermal Clad is normally purchased in one of the standard-gauge thicknesses. Non-standard thicknesses are also available. For ML-11006 multi-layer applications, 1.5 mm aluminum (5052 or 6061 alloy) is the most common base metal selection, offering a practical balance of thermal spreading, mechanical rigidity, weight, and machinability. Copper base is specified for the most thermally demanding designs.

Copper Foil Weight and Current Carrying Capability

The advantage of Thermal Clad is that the circuit trace interconnecting components can carry higher currents because of its ability to dissipate heat due to I²R loss in the copper circuitry.

For ML-11006 multi-layer builds, 1 oz and 2 oz copper are most common in inner layers. Heavier copper (3–6 oz) on outer power layers improves current carrying and heat spreading but increases lamination pressure requirements and demands verification with your fabricator’s qualified process parameters.

HiPot Testing Protocol

Any micro-fractures, delaminations or micro-voids in the dielectric will breakdown or respond as a short. Due to the capacitive nature of the circuit board construction, it is necessary to control the ramp up of the voltage to avoid nuisance tripping of the failure detect circuits in the tester and to maintain effective control of the test.

For ML-11006 multi-layer IMS boards, all completed assemblies should undergo hi-pot dielectric breakdown testing. Use a controlled voltage ramp of 100–500 V/s rather than step-application. Test voltage should be specified per IPC or UL requirements for your end application — typically 1.5–2× the working voltage.

Solder Mask and Surface Finish Compatibility

ML-11006 boards process through standard SMT solder mask and surface finish steps. ENIG (Electroless Nickel Immersion Gold) and HASL LF (Lead-Free Hot Air Solder Leveling) are both widely used. For applications requiring maximum thermal performance at the component pad interface, ENIG is preferred as it provides the flattest surface for SMD component solder joints.

Bergquist ML-11006 vs. Competing Multi-Layer IMS Dielectrics

A Note on Arlon Multi-Layer IMS Materials

Arlon PCB materials, particularly the 92ML series, are worth evaluating as an alternative when your project has strict military or aerospace qualification requirements. Arlon’s heritage in demanding environmental applications means their materials carry well-documented reliability data across temperature cycling, humidity exposure, and vibration profiles that some commercial IMS datasheets don’t fully address. For commercial industrial projects, the ML-11006 remains the most widely available and fabricator-qualified choice.

Useful Resources for Bergquist ML-11006 and Multi-Layer IMS Design

Official Documentation

• TCLAD Product Page — Board-Level Solutions — Current Henkel/TCLAD product information, multi-layer IMS capability overview, and contact for technical support
• Bergquist Thermal Clad Selection Guide (via Digikey) — The most comprehensive engineering reference for the full Thermal Clad product family, including CML/ML-series dielectrics, stack-up configurations, and assembly guidelines
• Bergquist MP-06503 TDS Reference (MCLPCB) — Representative TDS format for Bergquist Thermal Clad grades; ML-series format follows the same structure

Standards and Testing

• IPC-4101: Specification for Base Materials for Rigid and Multilayer Printed Boards — Qualification standard for laminate and prepreg materials
• ASTM D5470: Thermal Transmission Properties of Thin Thermally Conductive Solid Electrical Insulation — Primary thermal conductivity test method cited in Bergquist datasheets
• IPC-2221: Generic Standard on Printed Board Design — Design rules covering conductor spacing, voltage clearance, and current carrying capacity applicable to ML-11006 designs

Distributor and Supply

• Digi-Key Bergquist Thermal Substrates — Search “Bergquist TCLAD” for stocked IMS panels; ML-series may require inquiry for specific configurations
• Mouser Bergquist Products — Alternative stocking distributor with cross-reference capability
• NCAB Group IMS PCB Specifications — Useful third-party resource for IMS design rules and fabricator specifications

5 Frequently Asked Questions About Bergquist ML-11006

Q1: What exactly does the “ML” prefix in ML-11006 mean, and is it the same as CML?

Yes, ML and CML refer to the same product family. CML stands for Ceramic Multi-Layer, and the ML product code prefix is used in the commercial part numbering system. The “ML” in ML-11006 indicates this is a multi-layer capable dielectric available in prepreg form — with a glass carrier added specifically to enable handling and lamination in standard multilayer press equipment. The numbers that follow (110 for thermal conductivity, 06 for 6-mil thickness) encode the key performance parameters. When ordering through distributors or discussing with fabricators, ML-11006 and CML-11006 refer to the same material.

Q2: Can the ML-11006 be used as a drop-in replacement for standard FR4 prepreg in an existing multilayer design?

Partly, with caveats. The ML-11006 is physically compatible with standard multilayer lamination equipment and processes — that’s the whole point of the glass carrier. However, several design parameters will differ: the Tg of 130°C is on the lower end compared to modern high-Tg FR4 grades (150–180°C), so thermal cycling requirements need to be evaluated. The dielectric constant (~4.2–4.7) is similar to FR4, so impedance-controlled traces won’t change dramatically. The key benefit of swapping in ML-11006 is the thermal conductivity improvement — roughly 4–5× over standard FR4 — which enables higher-power components to be mounted without a separate heatsink or with a smaller metal base. Run your thermal model before and after the substitution to quantify the actual temperature reduction at your critical components.

Q3: What is the typical breakdown voltage of the ML-11006, and is it suitable for 480V AC industrial applications?

The ML-11006 at 6-mil dielectric thickness provides a typical dielectric breakdown voltage in the range of 5–7 kVAC. For applications with an expected voltage over 480 Volts AC, Bergquist recommends a dielectric thickness greater than 0.003″ (75µm). At 6 mil (152 µm), the ML-11006 is well above that minimum threshold and is generally suitable for 480V AC applications with appropriate creepage and clearance design. For applications at or above 690V AC, or any design subject to frequent inductive switching transients, evaluate the ML-11009 (9 mil) for additional voltage margin.

Q4: How does the ML-11006 compare to using thermal vias in a standard FR4 multilayer board?

Both approaches improve thermal performance over basic FR4, but they address the problem differently and at different performance levels. Thermal vias in FR4 can reduce junction-to-board thermal resistance by 20–40% depending on via density and copper weight — meaningful, but still limited by FR4’s poor bulk thermal conductivity (~0.24 W/m·K). The ML-11006 replaces FR4 prepreg with a 1.1 W/m·K dielectric, achieving roughly 4–5× better conduction through the bonding layers, independent of via drilling. In standard FR4 products, it is very difficult to dissipate a large amount of heat away from components. For designs where component power density is moderate (under ~3–5 W/cm²), thermal vias in FR4 may be sufficient and cheaper. Above that density, or where a metal base plate is part of the thermal design, ML-11006 in a true IMS construction delivers performance that thermal vias in FR4 cannot match.

Q5: Are there fabricators outside of Bergquist’s direct network who can process ML-11006 boards?

Yes. ML-11006 is among the Bergquist materials that several qualified Asian and Western PCB manufacturers can process, though availability varies by region. When qualifying a fabricator for ML-11006 production, confirm specifically that they have experience laminating CML prepreg in a multi-layer press cycle (not just single-layer IMS), that they can perform hi-pot dielectric testing on completed assemblies, and that their solder mask and surface finish processes are qualified on TCLAD substrates. Ask for previous production lot data or reliability test results if your application is safety-critical. Lead times for ML-series material are typically 4–8 weeks from non-stocking fabricators, so factor this into your program schedule.

Final Thoughts: Is the Bergquist ML-11006 Right for Your Design?

The ML-11006 answers a specific engineering question: how do you get the thermal management benefits of Bergquist Thermal Clad IMS technology into a design that genuinely needs more than one circuit layer?

If your design is a straightforward single-layer power LED board or a simple motor control circuit, the ML-11006 is probably not your best choice — the HPL, LTI, or HT grades offer better thermal conductivity and lower cost for those applications. But if you’re designing a multi-layer power electronics board where combining power and control layers on a thermally managed substrate is an engineering requirement rather than a preference, the ML-11006 is exactly the material the Bergquist product family developed for that scenario.

The prepreg form factor, multi-layer lamination capability, glass carrier handling, UL 94V-0 compliance, RoHS compliance, and reasonable thermal conductivity improvement over FR4 make it a practical and well-characterized choice for the specific intersection of “needs multiple signal layers” and “needs serious thermal management” that increasingly defines modern power electronics design.

For multi-layer IMS PCB fabrication using Bergquist ML-11006, TCLAD, and other thermally conductive dielectrics, work closely with your fabricator’s engineering team during stack-up development to ensure compatible lamination processes and qualified hi-pot testing procedures.

The post Bergquist ML-11006 Multi-Layer IMS PCB: Specifications & Application Guide appeared first on RayPCB.

Ordering a Bergquist MCPCB prototype is not the same as dropping a Gerber zip onto a commodity FR4 board service and hitting submit. The wrong material call, a missing fabrication note, or an ambiguous surface finish spec can push your lead time from 5 days to 3 weeks — or produce a board that fails hi-pot on the bench before you’ve even reflowed a single component. This guide walks through the entire ordering process the way an engineer who has done it before would explain it: what files you need, which Bergquist material to specify, where fabricators actually trip up, and how to compress turnaround time without cutting corners on quality.

Why Bergquist MCPCB Materials Require a Different Ordering Process

Most quick-turn fabricators stock one or two standard aluminum MCPCB laminates — typically a generic 1.0 W/m·K ceramic-filled epoxy dielectric bonded to 5052 aluminum. That covers a huge portion of the market. But Bergquist Thermal Clad materials — the HT series, HPL series, MP series, and CML series — are specified by engineers who need documented, certified dielectric performance, not just a thermal conductivity number on a marketing sheet.

When you specify a Bergquist product by name, you’re locking in a traceable supply chain. The dielectric breakdown voltage, peel strength, thermal resistance, and UL RTI rating come with lot traceability back to Henkel (which acquired Bergquist). Generic aluminum PCB laminates cannot give you that. For automotive LED modules, mains-connected LED drivers, and any board that needs UL or IEC certification, that traceability is not optional — it’s part of your compliance file.

The ordering process for a Bergquist MCPCB prototype, therefore, involves two parallel tasks: communicating the material specification clearly enough that your fabricator can source the correct laminate, and preparing Gerber files and fabrication notes that give the shop everything they need to process that laminate correctly.

Step 1: Select the Right Bergquist Thermal Clad Material

Before you write a single line in your fab notes, you need to confirm which Bergquist material is correct for your application. The most common point of confusion is between the HT series (high temperature, high voltage) and the HPL series (high power, thinner dielectric). Here’s the decision framework:

Bergquist Thermal Clad Selection by Application

The practical shortcut: if your board is mains-connected or referenced to a high-voltage bus, you need HT-04503 at minimum. If it’s in an automotive environment at continuous >130°C ambient, go HT-09009. If it’s a Class III or SELV-only LED lighting board running off a DC driver, HPL-03015 or HPL-04515 gives you the lowest thermal resistance with adequate isolation.

For applications requiring a different resin chemistry with specific CTE matching — satellite payloads, aerospace thermal cycling environments — look at Arlon PCB materials as an alternative dielectric family with different base chemistry.

Step 2: Prepare Your Gerber File Package

A complete Bergquist MCPCB prototype file package includes more than a standard FR4 Gerber set. Here’s what should be in your ZIP before you submit to any fabricator:

Required Files for MCPCB Prototype Submission

The fabrication notes document is where most prototype orders break down. Generic fab notes written for FR4 will not communicate everything your MCPCB fabricator needs. MCPCB-specific fabrication notes must include:

Material specification line: State the exact Bergquist material by full product name — not “2.2 W/m·K aluminum PCB” but “Bergquist Thermal Clad HT-04503 on 5052-H32 aluminum, 1.6mm total board thickness.”

Hi-pot requirement: State the test voltage explicitly. For HT-04503 that’s typically 1,500V AC or 2,121V DC minimum; for HT-09009, 3,000V AC is a reasonable specification. Without a stated hi-pot requirement in your notes, many shops run whatever their default is.

PTH clearance callout: If your design has plated through-holes, state the required clearance from hole wall to metal core edge in mils, and specify resin plug fill for all PTH clearance zones.

Solder mask color: LED boards almost universally specify white mask for light reflectance. State reflectance requirements if you have them (>85% at 450nm is typical for quality LED board suppliers).

Surface finish and shelf life: ENIG (Electroless Nickel Immersion Gold) is the preferred finish for fine-pitch SMT. Specify “ENIG per IPC-4552” if you want a standardized gold thickness.

Step 3: Choose a Fabricator That Stocks Bergquist Material

This is where many engineers waste prototype cycles. Not every quick-turn PCB shop stocks Bergquist Thermal Clad material. If your fab has to order it from Henkel’s distribution channel, add 5–10 business days to your lead time minimum. Before you submit files, ask the fabricator directly:

“Do you have Bergquist [specific product name] in stock in the thickness and copper weight I need?”

If the answer is no or uncertain, you have three options: wait for them to stock it, find a fabricator who keeps it in inventory, or ask whether they can source it from a local distributor on an expedited basis.

Fabricators who handle significant MCPCB volume — shops serving the automotive, LED, or power electronics sectors — are far more likely to maintain Bergquist stock. General-purpose quick-turn shops that treat MCPCB as a specialty item will not.

What to Ask When Qualifying a Fabricator for Bergquist MCPCB Prototype

Step 4: Understand Realistic Quick Turn Lead Times

The phrase “quick turn” means something different for MCPCB than for FR4. Here’s what to expect based on board complexity and material availability:

MCPCB Prototype Lead Time by Complexity

Two things compress lead time most reliably: clean Gerber files with complete fab notes on first submission (no DFM iteration cycles), and a fabricator who physically has your Bergquist material on the shelf.

Step 5: Review the DFM Feedback Before Release

Reputable MCPCB fabricators will return a DFM (Design for Manufacturability) check before cutting material. For Bergquist MCPCB prototypes, the DFM items most commonly flagged include:

PTH clearance violations: Through-holes too close to the metal core edge. Fix: verify all PTH holes have ≥40 mil clearance from core edge and are called out for resin plug fill.

Trace-to-edge clearance: Copper traces within 0.5mm of the routed board edge create shorts after aluminum deburring. Fix: confirm ≥20 mil copper-to-edge clearance on all layers.

Missing hi-pot requirement: Shop cannot default appropriately without it. Fix: state test voltage in fab notes explicitly.

Undefined surface finish over bare aluminum edges: After routing, the exposed aluminum edge may or may not be masked — define it, don’t leave it ambiguous.

Solder mask color defaulted to green: If your fab notes don’t specify white, you’ll get green. Fix: state color and, if relevant, specify the minimum light reflectance value.

Accept no DFM feedback means either your files were perfect (possible) or the shop didn’t check carefully (more likely). Either way, review any modifications the shop proposes before approving release to production.

Step 6: Specify Your Required Test Documentation

For engineering prototypes going into certification testing or thermal validation, the documentation you receive with the boards matters as much as the boards themselves. Request the following:

For most development prototypes, hi-pot test report and a material CoC are the minimum. Don’t discover you need a CoC after the boards are built — it’s much harder to generate retrospectively.

Common Mistakes When Ordering Bergquist MCPCB Prototypes

Useful Resources for Bergquist MCPCB Prototype Orders

Frequently Asked Questions About Bergquist MCPCB Prototypes

Q1: Can I order a Bergquist MCPCB prototype from standard online PCB services like JLCPCB or PCBWay?

Some online services offer aluminum MCPCB options, but they typically stock generic laminates rather than named Bergquist products. If you need a traceable Bergquist HT or HPL material with a CoC, you will need to work with a fabricator who explicitly lists Bergquist Thermal Clad as a stocked material. For development prototypes where generic 1.0–2.0 W/m·K aluminum suffices, commodity online services are a reasonable starting point. For certification builds or automotive-grade prototypes, go to a qualified MCPCB house.

Q2: What is the minimum order quantity for a Bergquist MCPCB prototype?

Most qualified MCPCB fabricators accept orders from 1–5 pieces for prototypes. Some shops impose a minimum order value (typically $150–$300) rather than a minimum piece count. Panelization — running multiple board designs on one panel — can help hit the minimum order value while getting multiple prototype designs fabbed in the same run.

Q3: How do I verify that the fabricator actually used Bergquist material and not a substitute?

Request a material Certificate of Conformance (CoC) with every prototype order. A legitimate CoC will reference the Bergquist product designation, lot number, and Henkel as the material manufacturer. Some engineers also request a cross-section coupon — a destructive sample that shows the dielectric and metal layers in cross-section — for first-article builds. If the dielectric thickness doesn’t match the Bergquist spec, you know something was substituted.

Q4: My design has a mix of PTH connectors and SMT components. What extra notes should I include in my fab package?

For any PTH component in a Bergquist MCPCB, your fab notes must specify: (1) the required clearance from hole wall to metal core edge in mils — 40 mils is a common minimum, 50 mils preferred; (2) that the clearance annular region around each PTH is to be resin-plug filled with non-conductive epoxy, cured, and surface-planarized before hole plating; and (3) that you want the PTH filled regions confirmed in the DFM report. Missing these notes is the most common cause of hi-pot failures on MCPCB boards with through-hole components.

Q5: How much more expensive is a Bergquist MCPCB prototype compared to standard aluminum MCPCB?

Material cost for Bergquist Thermal Clad runs roughly 2–4x higher than generic Chinese-sourced aluminum dielectric laminates per square foot, depending on which product. In prototype quantities, that material premium often translates to a total board cost 30–60% higher than a generic aluminum MCPCB of the same size. However, the cost difference compresses significantly at higher volumes (500+ pieces), and the traceability, documented electrical performance, and UL compliance value of Bergquist material often justifies the premium in certified-product designs where substituting an unverified laminate would require re-testing.

Meta Description Suggestions:

Option A — Tight, keyword-rich (155 characters): Step-by-step guide to ordering a Bergquist MCPCB prototype: material selection, Gerber file checklist, hi-pot specs, fabricator questions, lead times, and 5 engineer FAQs.

Option B — Value-forward (158 characters): How to order Bergquist MCPCB prototypes the right way — HT vs HPL material selection, fab note requirements, quick-turn lead times, test documentation, and common ordering mistakes.

Option C — Longer variant (~200 characters): Engineer’s quick-turn guide to Bergquist MCPCB prototypes: choose HT-04503 vs HT-09009 vs HPL, prepare complete Gerber packages with MCPCB-specific fab notes, verify material stock, and get hi-pot certified boards faster.

The post How to Order Bergquist MCPCB Prototypes: Quick Turn Guide appeared first on RayPCB.

If you’ve been sourcing Metal Core PCB (MCPCB) substrates for mid-range thermal applications, there’s a good chance you’ve come across the Bergquist LTI-04503. It occupies a well-defined niche in the Thermal Clad lineup — not the maximum-temperature beast that the HT series is, but also not the barebones general-purpose option. The LTI-04503 is the dielectric you reach for when your operating environment is moderate, your budget matters, and you still need genuine thermal performance backed by Bergquist’s decades of engineering credibility.

This guide walks through everything a PCB engineer actually needs to know: what LTI means in Bergquist’s naming convention, full material specifications, how it compares to sibling dielectrics, which applications it genuinely fits, and how to design with it effectively.

What Is the Bergquist LTI-04503?

Understanding the Thermal Clad Platform

Bergquist’s Thermal Clad Insulated Metal Substrate (IMS) was developed as a thermal management solution for higher watt-density surface mount applications where heat issues are a major concern. The entire platform is built around a three-layer construction: a copper circuit layer on top, a proprietary dielectric layer in the middle, and a metal base (typically aluminum) underneath.

The dielectric is a proprietary polymer/ceramic blend that gives Thermal Clad its excellent electrical isolation properties and low thermal impedance. The polymer is chosen for its electrical isolation properties, ability to resist thermal aging and high bond strengths. The ceramic filler enhances thermal conductivity and maintains high dielectric strength.

What “LTI” Means

In Bergquist’s product naming system, the prefix identifies the dielectric family. LTI stands for Low Temperature Insulator — a dielectric engineered specifically for applications that operate at moderate temperatures, as distinct from the HT (High Temperature) family, which is rated for far more aggressive thermal cycles. Bergquist references the LTI dielectric alongside FR-4 in comparative current-carrying capability charts, meaning it’s positioned as a step up from standard FR-4 in thermal performance while remaining suitable for standard temperature environments.

The 04503 suffix follows Bergquist’s standard numbering: “045” refers to the approximate total laminate stack, and “03” denotes the 3-mil (0.003″, approximately 76 µm) dielectric layer thickness.

Bergquist LTI-04503 sits within the broader Thermal Clad family alongside materials such as MP-06503, HT-07006, ML-11006, and HPL-03015, each targeting a different thermal performance tier and application environment.

Bergquist LTI-04503 Full Specifications

Core Physical & Thermal Properties

The table below summarizes the key properties of the LTI-04503 dielectric as used in the Bergquist Thermal Clad platform:

Note: Verify current specifications directly against the Bergquist/Henkel official datasheet before design lock-in, as formulations can be updated.

Laminate Stack Construction

Electrical Properties

How the LTI-04503 Fits Within the Bergquist Thermal Clad Family

One of the most common questions when selecting a Bergquist substrate is: which dielectric variant do I actually need? The table below helps clarify where the LTI-04503 lands relative to the other core options.

Bergquist Thermal Clad Dielectric Comparison

The LTI-04503 is the most cost-conscious of the group. For designs where junction temperatures will comfortably stay below the Tg (~130°C) and there’s no requirement to withstand extreme thermal cycling, the LTI-04503 offers a compelling balance of performance and economics. If your device sits at a higher steady-state temperature or goes through aggressive thermal shock testing, you’ll want to step up to the MP or HT series.

Key Advantages of the Bergquist LTI-04503

Proven Thermal Management Over FR-4

The single biggest reason to move to the LTI-04503 from conventional FR-4 is thermal conductivity. Standard FR-4 delivers approximately 0.2–0.3 W/m-K. Bergquist materials allow heat to be transferred more efficiently with thermal conductivity up to 9.0 W/m-K across the product range, and even the entry-level LTI-04503 at ~1.5 W/m-K is roughly five times better than FR-4. In real-world terms, this means substantially lower junction temperatures for the same power dissipation, which directly translates to longer component life.

UL-Recognized Dielectric

The dielectric layer has UL recognition, simplifying agency acceptance of final assemblies. For products destined for consumer markets in North America and Europe, this matters during safety certification — your UL file for the end product can reference the recognized dielectric rather than requiring a full re-test of the substrate material.

Automated Assembly Compatibility

Thermal Clad can reduce production costs by enabling automated pick-and-place equipment for SMDs. Unlike some ceramic or thick-film alternatives, the LTI-04503 plays nicely with standard SMT assembly lines. Standard stencil printing, reflow ovens, and automated optical inspection (AOI) all apply without special process accommodations.

RoHS and Halogen-Free Compliance

Thermal Clad substrates are RoHS compliant and halogen-free. The LTI-04503 meets current EU RoHS directives and supports lead-free solder processes, making it appropriate for products entering EU, UK, and other regulated markets.

Board Size Reduction and Hardware Elimination

Thermal Clad greatly reduces board space while replacing other components including heat sinks. It offers the opportunity to eliminate mica and grease or rubber insulators under power devices by using direct solder mount to Thermal Clad. By eliminating this hardware, heat transfer is improved. For a design that previously used a TO-220 device with mica washer, thermal grease, and a discrete finned heatsink, migrating to an LTI-04503 board can eliminate all that hardware and still achieve equal or better thermal performance.

Typical Applications for the Bergquist LTI-04503

The LTI-04503 hits its stride in applications where thermal performance needs to exceed what FR-4 can offer, but where the operating environment is not demanding enough to justify the premium of the HT or HPL series.

Consumer and Commercial Electronics

Standard LED driver circuits, power supply boards, and audio amplifier output stages are natural homes for the LTI-04503. If you’re building a class-D amplifier with MOSFETs running at moderate switching frequencies, or a 30–50W LED driver for commercial lighting, LTI-04503 gives you good heat spreading without paying for thermal headroom you’ll never use.

LED Lighting (Standard Output)

Metal core PCB and standard FR-4 are commonly used circuit board materials in conjunction with Power LEDs. Bergquist’s Thermal Clad dielectric is a thin, thermally conductive layer bonded to an aluminum or copper substrate for heat dissipation. The key to Thermal Clad’s superior performance lies in its dielectric layer — it offers electrical isolation with high thermal conductivity and bonds the base metal and circuit foil together. For LED luminaires where the LED junction temperature target is in the 85–100°C range and the ambient is well below 50°C, LTI-04503 is well-suited without overkill.

Power Conversion (Low-to-Mid Power Range)

Due to the size constraints and watt-density requirements in DC-DC conversion, Thermal Clad has become the favored choice. It is available in a variety of thermal performances, is compatible with mechanical fasteners and is highly reliable. For telecom PSU boards, industrial 24V power supplies, and battery management systems (BMS) operating at moderate power levels, the LTI-04503 offers an efficient and cost-effective substrate.

Automotive Ancillaries (Non-Powertrain)

For automotive interior electronics — ambient lighting drivers, seat heater controllers, climate control modules — where temperatures are moderate and the primary driver for moving off FR-4 is lifespan and reliability, the LTI-04503 checks the boxes. Bergquist PCBs are widely used for sparker and modifiers on fire for mobile and motorcycle, soundbox, power LED, acoustic shielding system and power supply modules.

Solid State Relays and Switching Devices

The implementation of Solid State Relays in many control applications calls for thermally efficient and mechanically robust substrates. Thermal Clad offers both. The material construction allows mounting configurations not reasonably possible with ceramic substrates.

Design Considerations When Using Bergquist LTI-04503

Circuit Flatness and Copper Thickness Ratio

Circuit flatness can be a concern when the base layer is aluminum. To achieve a flat circuit, maintain the proper ratio of circuit layer thickness to base. If the thickness of the copper circuit layer is kept at 10% of the base layer thickness or thinner, the aluminum base will mechanically dominate, keeping the circuit flat. In practice, with a 1.57 mm (0.062″) aluminum base, your copper circuit layer should stay at or below approximately 157 µm — roughly 4.5 oz copper — to maintain flatness. Most designs using 1 oz or 2 oz copper are well within this range.

Voltage Ratings and Dielectric Thickness

For applications with an expected voltage over 480 Volts AC, Bergquist recommends a dielectric thickness greater than 0.003″ (75 µm). The LTI-04503’s 3-mil dielectric is right at this threshold. If your design operates above 480 VAC, consider either using a thicker dielectric variant or applying additional creepage and clearance spacing in the PCB layout to remain within safety agency requirements.

Solder Process Compatibility

The LTI-04503 is compatible with standard lead-free reflow profiles (SAC305 alloys, peak temperatures around 260°C). The typical application technique for solder is a metal stencil. Dispensing of solder to specific locations is used for secondary operations or special attachment requirements. For the base metal, avoid excessive heat soaking — prolonged exposure above 260°C at the board level can stress the polymer-ceramic dielectric bond.

Proof Testing and Dielectric Integrity

Any micro-fractures, delaminations or micro-voids in the dielectric will break down or respond as a short. Due to the capacitive nature of the circuit board construction, it is necessary to control the ramp-up of the voltage to avoid nuisance tripping of the failure detect circuits in the tester and to maintain effective control of the test. When doing production hipot (high-potential) testing, use a controlled voltage ramp rate. A sudden step to the full test voltage on a Thermal Clad board will frequently cause false failures due to displacement current in the capacitive dielectric structure.

Trace Width and Current Capacity

Current carrying capability is a key consideration because the circuit layer typically serves as a printed circuit, interconnecting the components of the assembly. The advantage of Thermal Clad is that the circuit trace interconnecting components can carry higher currents because of its ability to dissipate heat due to I²R loss in the copper circuitry. Compared to FR-4, trace temperature rise for a given current is lower on LTI-04503, meaning you can effectively use slightly narrower traces for equivalent thermal performance — a useful benefit in space-constrained designs.

Manufacturing Process Overview for LTI-04503 PCBs

Getting a quality LTI-04503 board made requires working with a manufacturer who stocks genuine Bergquist material and understands MCPCB fabrication. The key process steps differ meaningfully from standard FR-4 manufacturing.

Step 1 – Material Procurement and Incoming Inspection

The raw laminate (copper foil + LTI dielectric + aluminum base) arrives in panel form. Incoming inspection should verify the dielectric thickness and visual integrity of the laminate.

Step 2 – Circuit Imaging and Etching

Standard photo-imaging and wet chemical etching applies. The aluminum base is masked to prevent attack during etching. Pattern tolerances follow standard IPC-2221 guidance.

Step 3 – Surface Finish Application

Common surface finish options include HASL (Hot Air Solder Leveling) — a 63/37 Pb/Sn or lead-free equivalent coating with excellent shelf life and solderability. OSP (Organic Solderability Protectant) is a thin coating to protect the copper with a shelf life of 3–6 months. FST (Flow Solderable Tin) is a relatively new planar coating with a long shelf life. ENIG (Electroless Nickel Immersion Gold) is also widely used for LTI-04503 boards, especially in applications requiring wirebonding or very fine pitch SMD.

Step 4 – Mechanical Fabrication

Routing, drilling, and scoring are performed using CNC equipment. Aluminum-base MCPCB requires carbide tooling and controlled feeds. V-scoring is a common option for panel depaneling.

Step 5 – Electrical and Dielectric Testing

Every Bergquist Thermal Clad board should undergo a hipot test to verify dielectric integrity. Production proof-test voltage is typically applied at a controlled ramp rate.

Bergquist LTI-04503 vs. Competing MCPCB Materials

While other manufacturers produce aluminum-base PCB laminates with comparable claimed specs, Bergquist’s Thermal Clad family — including the LTI-04503 — carries decades of field reliability data, UL recognition, and a rigorous qualification program. New Bergquist materials undergo a rigorous 12 to 18 month qualification program prior to being released to the market, with extensive testing on all thermal materials for electrical integrity, including mechanical property validation, adhesion, temperature cycling, and thermal and electrical stress testing to 2000 hours.

For engineers who want to compare LTI-04503 against other Insulated Metal Substrate (IMS) platforms, it’s worth noting that comparable alternatives exist from manufacturers such as Arlon PCB and others in the IMS laminate space. Arlon’s IMS products are worth evaluating if design requirements push outside the Bergquist standard range, though the LTI-04503 remains one of the most widely supported and documented IMS dielectrics in production worldwide.

Useful Resources and Datasheets for the Bergquist LTI-04503

Frequently Asked Questions About Bergquist LTI-04503

1. What does “LTI” stand for in Bergquist LTI-04503?

LTI stands for Low Temperature Insulator, referring to the specific dielectric formulation used in this Thermal Clad variant. It is designed for applications operating at moderate ambient and junction temperatures, making it distinct from Bergquist’s HT (High Temperature) series, which uses a more thermally robust polymer system rated for sustained high-temperature exposure. The LTI dielectric still significantly outperforms FR-4, but it is not the right choice if your board will see sustained temperatures approaching or exceeding 130°C.

2. What is the thermal conductivity of the Bergquist LTI-04503?

The LTI-04503 dielectric offers a thermal conductivity of approximately 1.5 W/m-K, compared to FR-4’s typical 0.2–0.3 W/m-K. While lower than the HT-04503 (~2.2 W/m-K) or the MP-06503 (~2.4 W/m-K), this figure is still roughly five to seven times better than standard fiberglass laminate. For the thermal loads typical of standard LED drivers, consumer audio, and general-purpose power electronics under 100W, 1.5 W/m-K is generally sufficient.

3. Can I use the Bergquist LTI-04503 for high-voltage applications?

The LTI-04503 with a 3-mil (76 µm) dielectric has a typical AC breakdown voltage of ≥ 3 kVAC and is suitable for many industrial and commercial applications. However, as noted in Bergquist’s own design guidelines, for applications with an expected voltage over 480 Volts AC, Bergquist recommends a dielectric thickness greater than 0.003″. If your application runs above 480 VAC, you should either use a thicker dielectric variant or apply appropriate creepage and clearance margins in the PCB layout per IEC 60664-1.

4. How does LTI-04503 compare to the HT-04503?

Both use a 3-mil dielectric (“03” suffix) but differ significantly in the dielectric formulation. The HT-04503 features a thermal conductivity of 4.1 W/m-K and is rated for high-temperature exposure, with a Tg of approximately 150°C. The LTI-04503 sits below this at roughly 1.5 W/m-K thermal conductivity and a Tg around 130°C. Practically, if your device operates below 100°C steady-state and doesn’t go through aggressive thermal cycling (-40°C to +150°C), LTI-04503 is typically sufficient and more cost-effective. Step up to HT-04503 or HT-07006 for LED high-bay lighting, automotive powertrain, EV chargers, or motor drives.

5. Where can I buy Bergquist LTI-04503 raw material or finished PCBs?

Raw Bergquist LTI-04503 laminate can be sourced through authorized distributors such as Digikey, Mouser, and Arrow Electronics. For fabricated PCBs using LTI-04503 material, many China-based MCPCB manufacturers keep genuine Bergquist stock, including manufacturers able to provide Bergquist LTI-04503, MP-06503, ML-11006, HT-07006, and HPL-03015 material in configurations such as 1.6 mm thick, single-sided, 1 oz, with ENIG surface finish and CNC routed outline. Always confirm your fabricator is using genuine Bergquist laminate if the certification trail matters for your end product.

Conclusion

The Bergquist LTI-04503 is a mature, well-characterized Insulated Metal Substrate dielectric that earns its place in any PCB engineer’s materials toolkit. It isn’t the headline act — that role belongs to the HT or HPL variants for extreme thermal applications — but for the broad middle ground of standard-power electronics where FR-4 falls short, the LTI-04503 delivers genuine thermal improvement, UL-recognized insulation, lead-free solder compatibility, and the backing of Bergquist’s extensive qualification history.

The key is to match the material to the application honestly. If your steady-state board temperature comfortably sits below 100–110°C, your power dissipation is moderate, and your budget is under pressure, LTI-04503 is the pragmatic choice. Push beyond those boundaries and the HT or MP series will serve you better.

All specifications should be verified against the most current official Bergquist/Henkel datasheet prior to use in production design. Material properties can vary by production lot and are subject to revision by the manufacturer.

Meta Description Suggestion

Suggested Meta Description (under 160 characters):

Complete Bergquist LTI-04503 specs, thermal properties, design guide & FAQ. Engineer’s reference for this low temperature dielectric MCPCB material — datasheets included.

Character count: 158 ✓

The post Bergquist LTI-04503 Low Temperature Dielectric PCB: Full Specifications & Complete Engineer’s Guide appeared first on RayPCB.